Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

 
Reply to this topicStart new topic
> Stock Push Rod Length
R Dub
post Mar 14 2019, 01:14 PM
Post #1


Member
**

Group: Members
Posts: 120
Joined: 29-August 17
From: Burbs of Chicago
Member No.: 21,387
Region Association: None



Can anyone verify what the stock push rod length is for these cars?

From my research the stock length is 271mm and the stock part# 021-109-301-A. I ordered 2 of these to replace the 2 bent ones that I have. I have no history of what push rods were in my motor so I just assumed they were stock but it doesn't appear that way as my 2 new ones are about 1/4" longer than what was in there. Just want to verify before I go buy 6 more stock rods.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Highland
post Mar 14 2019, 03:12 PM
Post #2


Senior Member
***

Group: Members
Posts: 511
Joined: 8-August 11
From: San Diego, CA
Member No.: 13,418
Region Association: Southern California



I just measured two of mine and get 275.6 mm and 275.9 mm.

So just under a 1/4" longer than yours.

Do you have your actual pushrod lengths?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
R Dub
post Mar 14 2019, 03:30 PM
Post #3


Member
**

Group: Members
Posts: 120
Joined: 29-August 17
From: Burbs of Chicago
Member No.: 21,387
Region Association: None



QUOTE(Highland @ Mar 14 2019, 04:12 PM) *

I just measured two of mine and get 275.6 mm and 275.9 mm.

So just under a 1/4" longer than yours.

Do you have your actual pushrod lengths?


The car is back at my parents but my dad measured one that came out of the motor and said it was 10.25 inches so about 260mm.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Highland
post Mar 14 2019, 03:56 PM
Post #4


Senior Member
***

Group: Members
Posts: 511
Joined: 8-August 11
From: San Diego, CA
Member No.: 13,418
Region Association: Southern California



Forgot to mention aircooled.net sells custom cut aluminum pushrods assembled.

Do you have the rebuild history on the motor? Someone may have installed custom length pushrods to achieve correct valve geometry.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
mgphoto
post Mar 14 2019, 06:57 PM
Post #5


"If there is a mistake it will find me"
***

Group: Members
Posts: 1,330
Joined: 1-April 09
From: Los Angeles, CA
Member No.: 10,225
Region Association: Southern California



Post a couple of photos of both.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
rudedude
post Mar 14 2019, 07:49 PM
Post #6


Senior Member
***

Group: Members
Posts: 508
Joined: 1-January 05
From: minneapolis, mn
Member No.: 3,387
Region Association: Upper MidWest



I'm sure there are many used stock pushrods around if you ask. i probably have 5 sets that i don't know why I'm saving.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
bdstone914
post Mar 15 2019, 03:14 AM
Post #7


bdstone914
****

Group: Members
Posts: 4,496
Joined: 8-November 03
From: Riverside CA
Member No.: 1,319



Do you have a solid or hydraulic lifter engine?
You need to measure one of your non bent pushrods.

You may have custom lenght rods which is commom depending on how the engine was built.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
R Dub
post Mar 15 2019, 11:46 AM
Post #8


Member
**

Group: Members
Posts: 120
Joined: 29-August 17
From: Burbs of Chicago
Member No.: 21,387
Region Association: None



QUOTE(mgphoto @ Mar 14 2019, 07:57 PM) *

Post a couple of photos of both.


Will do once I can get back there to snap a pick of the ones that were in it.

QUOTE(bdstone914 @ Mar 15 2019, 04:14 AM) *

Do you have a solid or hydraulic lifter engine?
You need to measure one of your non bent pushrods.

You may have custom lenght rods which is commom depending on how the engine was built.


It had a hydraulic lifters in it. I am switching over to solid based on the advise of this forum.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
914sgofast2
post Mar 15 2019, 12:20 PM
Post #9


Senior Member
***

Group: Members
Posts: 606
Joined: 10-May 13
From: El Dorado Hills, CA
Member No.: 15,855
Region Association: None



You need to replace all your pushrods if you are converting from hydraulic to solid lifters. Solid lifters need the aluminum pushrods while the hydraulic lifters use steel pushrods.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Mark Henry
post Mar 15 2019, 02:13 PM
Post #10


that's what I do!
***************

Group: Members
Posts: 20,065
Joined: 27-December 02
From: Port Hope, Ontario
Member No.: 26
Region Association: Canada



QUOTE(R Dub @ Mar 15 2019, 01:46 PM) *

QUOTE(mgphoto @ Mar 14 2019, 07:57 PM) *

Post a couple of photos of both.


Will do once I can get back there to snap a pick of the ones that were in it.

QUOTE(bdstone914 @ Mar 15 2019, 04:14 AM) *

Do you have a solid or hydraulic lifter engine?
You need to measure one of your non bent pushrods.

You may have custom lenght rods which is commom depending on how the engine was built.


It had a hydraulic lifters in it. I am switching over to solid based on the advise of this forum.


You can't just switch out the lifters, you have to change the cam as well.
Hydraulic cam has a different profile than the stock FI cam, and there also was mild performance hydraulic carb cams.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
R Dub
post Mar 16 2019, 06:18 PM
Post #11


Member
**

Group: Members
Posts: 120
Joined: 29-August 17
From: Burbs of Chicago
Member No.: 21,387
Region Association: None



QUOTE(Mark Henry @ Mar 15 2019, 03:13 PM) *

You can't just switch out the lifters, you have to change the cam as well.
Hydraulic cam has a different profile than the stock FI cam, and there also was mild performance hydraulic carb cams.


Yeah I have a new Web cam grind #86 with new solid lifters and a new cam gear on the way. I'm hoping that the stock push rods will work with this cam and the heads. Will have to check once I get the cam in and the heads back from Adrian at Headflow Masters
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
R Dub
post Mar 17 2019, 09:38 AM
Post #12


Member
**

Group: Members
Posts: 120
Joined: 29-August 17
From: Burbs of Chicago
Member No.: 21,387
Region Association: None



Here's a picture of the different ones. Hopefully you can see how much bigger in diameter the new one is.

(IMG:http://www.914world.com/bbs2/uploads_offsite/i582.photobucket.com-21387-1552837093.1.jpg)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Mark Henry
post Mar 18 2019, 05:57 AM
Post #13


that's what I do!
***************

Group: Members
Posts: 20,065
Joined: 27-December 02
From: Port Hope, Ontario
Member No.: 26
Region Association: Canada



QUOTE(R Dub @ Mar 16 2019, 08:18 PM) *

QUOTE(Mark Henry @ Mar 15 2019, 03:13 PM) *

You can't just switch out the lifters, you have to change the cam as well.
Hydraulic cam has a different profile than the stock FI cam, and there also was mild performance hydraulic carb cams.


Yeah I have a new Web cam grind #86 with new solid lifters and a new cam gear on the way. I'm hoping that the stock push rods will work with this cam and the heads. Will have to check once I get the cam in and the heads back from Adrian at Headflow Masters


Web cam grind #86 is a mild carb cam, much like the Scat C25, but it still requires HD single springs, Manton Cr-Mo steel cut to length PR, 1.7 modified rockers and 911 adjusters. The HD springs can bend the aluimum PR.

User is offlineProfile CardPM
Go to the top of the page
+Quote Post
brant
post Mar 18 2019, 09:50 AM
Post #14


914 Wizard
**********

Group: Members
Posts: 11,584
Joined: 30-December 02
From: Colorado
Member No.: 47
Region Association: Rocky Mountains



if you are changing the cam and lifters...
a full rebuild then....


you really need to measure and cut the correct length of push rods to take full advantage of the valve train/cam geometry

this is a precise measurement
the length of the pushrod effects the ratio of the rocker and how much valve lift you will get from the cam. skipping this step means you likely have too much or more likely too little lift. You essentially do not get the performance out of your cam lobes and could of just left the hydraulic cam alone if you don't perform this necessary step.

you need to read the articles on measuring push rods.
you will need an adjustable push rod to take measurements and then
transfer that measurement to your new pushrods to cut them to the correct lengths

you need a dial indicator, a mounting base, a timing wheel, an a large set of calipers to go longer than a push rod

this is a 4-8 hour job that is completed during re-assembly
you should also have already purchased the correct 1.7 rockers with the correct swivel feet. Modify the rockers to accept the swivel feet

do it right
its time and money, but a motor rebuild is no place to cut corners.
someone here can likely loan you some tools, or walk you through the process.

there are good tech articles, including Jakes that can help
User is offlineProfile CardPM
Go to the top of the page
+Quote Post

Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 



- Lo-Fi Version Time is now: 29th March 2024 - 03:12 AM