id plates from Germany, finally here way too expensive though |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
id plates from Germany, finally here way too expensive though |
dr914@autoatlanta.com |
Nov 19 2008, 04:07 PM
Post
#1
|
914 Guru Group: Members Posts: 7,900 Joined: 3-January 07 From: atlanta georgia Member No.: 7,418 Region Association: None |
finally found some of them had been previously engraving!
(IMG:http://autoatlanta.net/pictures/image001.jpg) (IMG:http://autoatlanta.net/pictures/image002.jpg) (IMG:http://autoatlanta.net/pictures/image003.jpg) (IMG:http://autoatlanta.net/pictures/image004.jpg) |
davep |
Nov 19 2008, 04:23 PM
Post
#2
|
914 Historian Group: Benefactors Posts: 5,156 Joined: 13-October 03 From: Burford, ON, N0E 1A0 Member No.: 1,244 Region Association: Canada |
Very nice. What about the proper stamps for them?
|
dr914@autoatlanta.com |
Nov 19 2008, 04:38 PM
Post
#3
|
914 Guru Group: Members Posts: 7,900 Joined: 3-January 07 From: atlanta georgia Member No.: 7,418 Region Association: None |
|
markb |
Nov 19 2008, 04:42 PM
Post
#4
|
914less :( Group: Members Posts: 5,449 Joined: 22-January 03 From: Nipomo, CA Member No.: 180 Region Association: Central California |
are the proper rivets available?
|
r_towle |
Nov 19 2008, 04:56 PM
Post
#5
|
Custom Member Group: Members Posts: 24,591 Joined: 9-January 03 From: Taxachusetts Member No.: 124 Region Association: North East States |
I have not looked at the 914 but if the rivets are the same as the 356 ID plates then the rivets are available.
Rich |
dr914@autoatlanta.com |
Nov 19 2008, 05:09 PM
Post
#6
|
914 Guru Group: Members Posts: 7,900 Joined: 3-January 07 From: atlanta georgia Member No.: 7,418 Region Association: None |
|
So.Cal.914 |
Nov 19 2008, 05:42 PM
Post
#7
|
"...And it has a front trunk too." Group: Members Posts: 6,588 Joined: 15-February 04 From: Low Desert, CA./ Hills of N.J. Member No.: 1,658 Region Association: None |
Ok, I'll bite...How Much?
|
dr914@autoatlanta.com |
Nov 20 2008, 11:26 AM
Post
#8
|
914 Guru Group: Members Posts: 7,900 Joined: 3-January 07 From: atlanta georgia Member No.: 7,418 Region Association: None |
|
So.Cal.914 |
Nov 20 2008, 11:28 AM
Post
#9
|
"...And it has a front trunk too." Group: Members Posts: 6,588 Joined: 15-February 04 From: Low Desert, CA./ Hills of N.J. Member No.: 1,658 Region Association: None |
|
r_towle |
Nov 20 2008, 11:41 AM
Post
#10
|
Custom Member Group: Members Posts: 24,591 Joined: 9-January 03 From: Taxachusetts Member No.: 124 Region Association: North East States |
Do you have the correct rivets for the plate in the front trunk near the headlight bucket?
This one , along with the door jamb one, should come off for a decent paint job...most I have seen are masked (poorly) and left in place. Also, when acid dipping, they need to come off or they get destroyed anyways. Rich |
Lo-Fi Version | Time is now: 15th June 2024 - 04:53 PM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |