IPB WARNING [2] Creating default object from empty value (Line: 113 of \modules\blog\rss.php)
My Blog Syndication Tue, 09 Jun 2026 06:02:01 +0000 notification@914world.com (914World.com) Invision Community Blog 60 replaced the bottom piece to the trunk latch (only to find the top piece is worn out too
and riveted in the door thresholds

hardly a list of monumental accomplishments... but after a rough day at work. it was good enough.]]> Sat, 31 Oct 2009 02:32:24 +0000
new AA pistons and Cylinders
webcam 163 grind
911 swivel feet
Raby webcam lifters
.015 deck height.
9.5:1 compression.
9lb 15.8 oz flywheel
1.8 205AA dizzy 32 degrees total advance, carb modified for vacuum advance.
modified CB performance linkage.
crane xr700 ignition
]]> Wed, 07 Oct 2009 02:11:04 +0000
the koni yellows are installed up front in place of the worn out KYBs... new ball joints and tie rod ends as well... not much progress, I know, but it's something...]]> Wed, 24 May 2006 18:42:16 +0000
engine tin seals are in, the clutch,Press. Plate are back in place, cables and pedal cluster is in, the rust holes in the long have been cut out. so, it's getting there... little by little...

oh, and the dash is painted... hammerite silver!
here's some pics.


]]> Fri, 15 Jul 2005 21:49:13 +0000
I have some used Koni Yellows, waiting to go on the front. I plan to do those and the ball joints soon.

I finally got a welder to fix the rust spots... just need to get off my ass and do it.

other "little things" on the to do list:
engman's rear trunk release kit to be installed
engine tin seals
new cables followed by installing the Shea-rebuilt pedal cluster
install the upper and lower dash, seats, console, backpad...

]]> Wed, 06 Jul 2005 20:07:05 +0000 ) I found more rust when grinding up sealant... in the passenger side firewall corner
]]> Sat, 21 May 2005 19:24:00 +0000

]]> Fri, 20 May 2005 16:14:16 +0000
rust along the side brace, haven't decided how to proceed there, need to dig more before I decide...... the rest is in pretty good shape so far, except one seat hing is rusted away... the PO had welded the seat rail to the pan instead of finxing the hinge


I also primered the metal dash... it's staying metal... a grey hammerite finish for the final...


]]> Fri, 06 May 2005 02:48:21 +0000 I replaced the brakes with Eric Shea's rebuilt calipers,
replaced the altenator with a rebuilt one (and voltage regulator)
exorcised some of the electrical demons,
fixed the parking brake (though one cable still seems "too long"... further investigation is required.
invested in an optima battery


still to do before driving it...
I have a leak in the gas tank, I think it's the old return hose, but need to check it out... "FIXED" 4/17/05 but still needs testing...
I have found some rust under the jack post... nothing terrible, but needs to be fixed ASAP
the other side is much worse, jack post and triangular piece at the front are both bad...
I need to prep/paint the floorpan and then install sound dampener and carpet kit... so I can install the seats/backpad.
]]> Tue, 29 Mar 2005 17:06:01 +0000 I replaced the brakes with Eric Shea's rebuilt calipers,
replaced the altenator with a rebuilt one (and voltage regulator)
exorcised some of the electrical demons,
fixed the parking brake (though one cable still seems "too long"... further investigation is required.
invested in an optima battery


still to do before driving it...
I have a leak in the gas tank, I think it's the old return hose, but need to check it out... "FIXED" 4/17/05 but still needs testing...
I have found some rust under the jack post... nothing terrible, but needs to be fixed ASAP
the other side is much worse, jack post and triangular piece at the front are both bad...
I need to prep/paint the floorpan and then install sound dampener and carpet kit... so I can install the seats/backpad.






]]> Tue, 29 Mar 2005 17:06:01 +0000