 Sorting Front Suspension, How to loosen steering Rack? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
  |
| ber914 |
 May 31 2004, 03:09 AM
Post
#1
|
|
Newbie  Group: Members Posts: 43 Joined: 8-April 04 From: Sydney, Australia Member No.: 1,908  |
I am busy sorting out my front suspension and want to fit bump steer spacers. Where do I loosen the steering rack on the steering column in order to lift it up to make space for the bump steer spacers?
Robert |
   |
 
|
| ArtechnikA |
May 31 2004, 04:49 AM
Post
#2
|
|
rich herzog Group: Members Posts: 7,390 Joined: 4-April 03 From: Salted Roads, PA Member No.: 513 Region Association: None |
QUOTE(ber914 @ May 31 2004, 01:09 AM) Where do I loosen the steering rack on the steering column in order to lift it up to make space for the bump steer spacers? at the base of the column shaft you will find one of the two U-joints that form the Z-bend. the U-joints have splined ends and Dutchman clamps. loosen the clamps, collapse the shafts into the joint. you may have to do the other one at the other end of the intermediate shaft too, but i think i just did the top one and it was enough. make sure the bolts on the clamps are tight when you're done. |
|
|
|
| ber914 |
May 31 2004, 05:36 AM
Post
#3
|
|
Newbie Group: Members Posts: 43 Joined: 8-April 04 From: Sydney, Australia Member No.: 1,908 |
Thamks. Do I access the U joints from inside the cabin or do I have to remove the fuel tank?
Robert |
|
|
|
| ArtechnikA |
May 31 2004, 05:46 AM
Post
#4
|
|
rich herzog Group: Members Posts: 7,390 Joined: 4-April 03 From: Salted Roads, PA Member No.: 513 Region Association: None |
QUOTE(ber914 @ May 31 2004, 03:36 AM) Thamks. Do I access the U joints from inside the cabin or do I have to remove the fuel tank? in a LHD car it's pretty easy to get at the upper U-joint inside the cabin, under the dash; i presume it's the same for a RHD car but i've never seen one, so YMMV. the lower one is, i believe - accessible from underneath, via the access panel - but it's been too long for me to remember, sorry ... give it a go with the upper joint and see if that doesn't work for you. unless you've found a way to raise the rack A LOT more than normal, it should do the trick ... |
|
|
|
| SirAndy |
May 31 2004, 02:05 PM
Post
#5
|
|
Resident German Group: Admin Posts: 41,679 Joined: 21-January 03 From: Oakland, Kalifornia Member No.: 179 Region Association: Northern California |
only one u-joint. it's inside the car ...
if you just install the spacers, you might not even have to undo that u-joint. just loosening the streering rack bolts from underneath should be enough. btw. make sure you got the longer bolts so you get enough thread with those spacers! Andy |
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th June 2024 - 12:46 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.