Shift Bushing Replacement Question |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
Shift Bushing Replacement Question |
Highland |
May 24 2013, 04:56 PM
Post
#1
|
Senior Member Group: Members Posts: 513 Joined: 8-August 11 From: San Diego, CA Member No.: 13,418 Region Association: Southern California |
From what I've read this pin shown in the picture is suppose to press out. I guess many have used a vice for a press. I destroyed the old bushing with this method and got it out, but the pin won't budge and looks to be one piece to me.
Am I missing something or do I just need to take it to a mechanic with a press? |
dlee6204 |
May 24 2013, 04:59 PM
Post
#2
|
Howdy Group: Members Posts: 2,162 Joined: 30-April 06 From: Burnsville, NC Member No.: 5,956 |
You're correct that the pin should press out. I've never had a problem doing so.
|
r_towle |
May 24 2013, 05:15 PM
Post
#3
|
Custom Member Group: Members Posts: 24,588 Joined: 9-January 03 From: Taxachusetts Member No.: 124 Region Association: North East States |
Long socket that fits inside the aluminum and puts the pressure on the steel.
Hammer out the pin. Put zero force or pressure on the cast piece |
TheCabinetmaker |
May 24 2013, 05:22 PM
Post
#4
|
I drive my car everyday Group: Members Posts: 8,304 Joined: 8-May 03 From: Tulsa, Ok. Member No.: 666 |
If it has evidence of being hammered, it might be "peened"on the end.
It will take a pretty stout vice to get it out. I've seen a couple that took a 10 ton press to remove. It should be a press fit. Don't want it coming out. |
914Sixer |
May 24 2013, 05:30 PM
Post
#5
|
914 Guru Group: Members Posts: 8,903 Joined: 17-January 05 From: San Angelo Texas Member No.: 3,457 Region Association: Southwest Region |
Soak it in PB Blaster for a day or so, then get started.
|
Java2570 |
May 24 2013, 06:21 PM
Post
#6
|
Senior Member Group: Members Posts: 649 Joined: 7-May 11 From: Fishers, IN Member No.: 13,035 Region Association: Upper MidWest |
Long socket that fits inside the aluminum and puts the pressure on the steel. Hammer out the pin. Put zero force or pressure on the cast piece This is how I just did mine....it took a little effort to get it started moving but really was no big deal. The socket works well at getting the force where it needs to be. |
tomeric914 |
May 24 2013, 06:33 PM
Post
#7
|
One Lap of America in a 914! Group: Members Posts: 1,259 Joined: 25-May 08 From: Syracuse, NY Member No.: 9,101 Region Association: North East States |
The pin seems to have a slight taper towards the center so it will get easier as you continue to press.
|
stugray |
May 24 2013, 09:47 PM
Post
#8
|
Advanced Member Group: Members Posts: 3,825 Joined: 17-September 09 From: Longmont, CO Member No.: 10,819 Region Association: None |
I just did this the other day too.
I used a bolt slightly smaller than the pin on one side. I put a deep well socket on the other and clamped it in my vice. It took a LOT more force than I thought to push it out, but it came out. I have yet to put it back in, but I test fit the new bushings and I am disappointed. The newer black ones seem a lot less firm than the stock white one was when I decided to "fix" it. Its kind of a PITA getting the black bushings into the Al. housing too. The shaft is hanging in the garage with a fresh coat of primer. Stu |
Highland |
May 24 2013, 11:22 PM
Post
#9
|
Senior Member Group: Members Posts: 513 Joined: 8-August 11 From: San Diego, CA Member No.: 13,418 Region Association: Southern California |
Thanks for all the responses. I wimped out and took the shift rod to a mechanic. He pressed out the pin and pressed it back in with the new bushings for $5. Just drove it around the block, but I think this may be the best the shifter has ever felt.
|
Jmedeiros |
May 25 2013, 12:43 AM
Post
#10
|
Member Group: Members Posts: 99 Joined: 12-November 12 From: Los Banos, CA Member No.: 15,138 Region Association: Northern California |
|
Lo-Fi Version | Time is now: 9th June 2024 - 03:34 AM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |