Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

2 Pages V  1 2 >  
Reply to this topicStart new topic
> 44 IDF early vs. late style, is one preferred over the other?
nebreitling
post Dec 6 2004, 05:38 PM
Post #1


Member Emeritus
****

Group: Members
Posts: 3,314
Joined: 26-March 03
From: San Francisco
Member No.: 478



the main difference, from what i can tell, is in the accelerator pump linkage and diaphram. i have the early style...


these carbs are in extremely rough shape and are currently going through a total rebuild right now.

as long as they're apart, is the late model perfered for any reason?


thx, n
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Aaron Cox
post Dec 6 2004, 05:39 PM
Post #2


Professional Lawn Dart
***************

Group: Retired Admin
Posts: 24,541
Joined: 1-February 03
From: OC
Member No.: 219
Region Association: Southern California



buy the weber IDF update kit...
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
nebreitling
post Dec 6 2004, 05:46 PM
Post #3


Member Emeritus
****

Group: Members
Posts: 3,314
Joined: 26-March 03
From: San Francisco
Member No.: 478



who's got it? i've been looking for it...
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
nebreitling
post Dec 6 2004, 05:48 PM
Post #4


Member Emeritus
****

Group: Members
Posts: 3,314
Joined: 26-March 03
From: San Francisco
Member No.: 478



oh, you mean the CB kit...

this doesn't address the early style accelerator pump diaphram and cam system...
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
lapuwali
post Dec 6 2004, 07:17 PM
Post #5


Not another one!
****

Group: Benefactors
Posts: 4,526
Joined: 1-March 04
From: San Mateo, CA
Member No.: 1,743



The main difference I know of is the accel linkage on the new style is adjustable without having to resort to a grinder or a welder. I've heard of several cases now with the old style Webers where the accel pump delivers way more fuel than required per stroke, and cutting this back will help both drivability and mileage. At least two setups I know of (including mine) also dribbled fuel out the accelerator pump while the engine was idling, until the pump cam was ground down a tad. Smelly idle and terrible mileage.

Other than that, there are minor differences on things like whether or not any vacuum ports are open, or blind plugged, or not there at all. I'd personally be happier if I had the new style, but the old style can be made to work. Of course, I'm switching to EFI as soon as I can make it happen (and I'm operating in Mueller time these days...)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
jwalters
post Dec 6 2004, 07:53 PM
Post #6


Sooo Close.......
***

Group: Members
Posts: 1,677
Joined: 14-May 04
From: Huntsville, AL
Member No.: 2,068
Region Association: Europe



(IMG:style_emoticons/default/wink.gif) I fixed that dribbling accel pump problem by using that other cb conversion kit--the one that has a new linkage plate with a round tension spring on each carb link plate--this eliminated my need for an external spring on each carb, and made the pedal MUCH more easily modulated, and it took care of the dribble, the real problem was that cross-bar linkage P.O.S.!!! I ditched that for a scat low-rider style linkage that bolts to the case split line-----wayyyy easy to set up!!!! (IMG:style_emoticons/default/smilie_pokal.gif) (IMG:style_emoticons/default/smilie_pokal.gif) (IMG:style_emoticons/default/beer.gif)

And it is outta the way--very clean install!!!!!!!!!!!
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
lapuwali
post Dec 6 2004, 09:15 PM
Post #7


Not another one!
****

Group: Benefactors
Posts: 4,526
Joined: 1-March 04
From: San Mateo, CA
Member No.: 1,743



I have the round throttle arm springs on each carb, but still needed a third spring on the linkage to provide the *snap* close I wanted. I don't like throttles that stick open. I still had the dribbling pump on one carb.

I used the CB crossbar linkage because that's what everyone else said was the best there was...
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Brett W
post Dec 7 2004, 12:21 AM
Post #8


Advanced Member
****

Group: Members
Posts: 2,858
Joined: 17-September 03
From: huntsville, al
Member No.: 1,169
Region Association: None



"everyone" was wrong. The center pull twist linkage is much better. Infact I am scrapping a CB cross bar linkage from this motor I just built and will be running the Bug Pack bellcrank. Although modified quite a bit.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
jwalters
post Dec 7 2004, 08:40 AM
Post #9


Sooo Close.......
***

Group: Members
Posts: 1,677
Joined: 14-May 04
From: Huntsville, AL
Member No.: 2,068
Region Association: Europe



QUOTE(lapuwali @ Dec 6 2004, 07:15 PM)
I have the round throttle arm springs on each carb, but still needed a third spring on the linkage to provide the *snap* close I wanted. I don't like throttles that stick open. I still had the dribbling pump on one carb.

I used the CB crossbar linkage because that's what everyone else said was the best there was...

(IMG:style_emoticons/default/ohmy.gif) The reason you are having to do this is because you have one or both ball bearings on the ends of the shaft gone bad!!!!

The good news is because they are a spec ball bearing, all you need is a p/n and go to your nearest industrial supply store and get some more.

Another affair that could be giving you trouble is one or both of the butterflies have slipped in the pinch bar.

Hold them up to a light and look thru it--with the idle screw backed all the way out you should not see any light at all--if you do, that butterfly has slipped, but that is an easy fix!
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
cha914
post Dec 7 2004, 09:18 AM
Post #10


MUSR 8 - 5lug conversion done wed - drive 500miles thrus
***

Group: Members
Posts: 739
Joined: 31-December 02
From: Austin, TX
Member No.: 63



Funny, I was told by "everyone" that the CB crossbar linkage was the best also...so who makes the centerpull twist linkage?

bugpack - is it decent, what kinda mods did you have to do?
scat - how expensive, is it any better than the bugpack?

anyone else?

What exactly don't you like about the crossbar linkage?

Thanks,

Tony
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Matt Romanowski
post Dec 7 2004, 09:23 AM
Post #11


Senior Member
***

Group: Members
Posts: 878
Joined: 4-January 04
From: Manchester, NH
Member No.: 1,507



The best is the Triad. The CB is just aweful.

Matt
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
rhodyguy
post Dec 7 2004, 09:48 AM
Post #12


Chimp Sanctuary NW. Check it out.
***************

Group: Members
Posts: 22,192
Joined: 2-March 03
From: Orion's Bell. The BELL!
Member No.: 378
Region Association: Galt's Gulch



you got that right matt. finally something i can comment on.

kevin
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Aaron Cox
post Dec 7 2004, 11:27 AM
Post #13


Professional Lawn Dart
***************

Group: Retired Admin
Posts: 24,541
Joined: 1-February 03
From: OC
Member No.: 219
Region Association: Southern California



triad is like 200 bucks tho....

the cb unit is the BEST for the BUCK. the crossbar never binds, and its not made out of thin sheet steel like bugpack etc.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Matt Romanowski
post Dec 7 2004, 12:00 PM
Post #14


Senior Member
***

Group: Members
Posts: 878
Joined: 4-January 04
From: Manchester, NH
Member No.: 1,507



It may be $200, but it is one of the best investments out there. I can't think of a better thing to spend $200 on. It would help every carbed car I've seen to date.

Matt
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
crash914
post Dec 7 2004, 12:44 PM
Post #15


its a mystery to me
***

Group: Members
Posts: 1,827
Joined: 17-March 03
From: Marriottsville, MD
Member No.: 434
Region Association: MidAtlantic Region



I think that I can comment..... (IMG:style_emoticons/default/blink.gif)

I just had matt over to look at why my car ran like s*it...mis adjusted carb linkage...I am running the redline webber linkage...matt thought it was just like the CB linkage....anyway, very hard to dial in both sides and not have a problem on either idle or WOT.....

I am now thinking about the Triad...
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Brett W
post Dec 7 2004, 01:46 PM
Post #16


Advanced Member
****

Group: Members
Posts: 2,858
Joined: 17-September 03
From: huntsville, al
Member No.: 1,169
Region Association: None



The Bug pack center pull linkage uses to different length arms. The pivot point is mounted off center of the engine case. You have to grind the legs off the stand and make it fit in the saddle beside one of the perimeter bolts. This will locate the pivot closer the center of the case. You will also need to weld two washers that you can fit to a much closer tolerance than the factory pivot hole. You will also need to relocate the binder bolt as well. Once that is done you need to build two equal length arms with good pivot balls on each end. once this is done you will need to build a stand to mount the throttle cable. ONce that is done you can go through the process of equalizing the arms and making sure that the travel is exactly the same on both sides of the carbs.

Yes it is labor intensive but this is the best linkage I have found. Until I finish my ball bearing pivot design this one goes on the last engine I built.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
cha914
post Dec 7 2004, 02:05 PM
Post #17


MUSR 8 - 5lug conversion done wed - drive 500miles thrus
***

Group: Members
Posts: 739
Joined: 31-December 02
From: Austin, TX
Member No.: 63



Brett...

Thanks for the writeup, doesn't really sound that bad...do you have a partnumber?

and of course, a picture of your setup would be great (IMG:style_emoticons/default/smash.gif)

Tony
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
cha914
post Dec 7 2004, 04:02 PM
Post #18


MUSR 8 - 5lug conversion done wed - drive 500miles thrus
***

Group: Members
Posts: 739
Joined: 31-December 02
From: Austin, TX
Member No.: 63



Ok...I have found mention of a Kadron center pull linkage from both bugpack and on aircooled.net, both are around ~60 bucks, but no pics available...I am guessing these are the same.

this the one you are talking about Brett?

Tony
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Brett W
post Dec 7 2004, 06:14 PM
Post #19


Advanced Member
****

Group: Members
Posts: 2,858
Joined: 17-September 03
From: huntsville, al
Member No.: 1,169
Region Association: None



Yeah. I can't remember which one it is though. Don't know the difference. I will see if I can get a camera to take a few pictures before and after the install.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Aaron Cox
post Dec 7 2004, 06:19 PM
Post #20


Professional Lawn Dart
***************

Group: Retired Admin
Posts: 24,541
Joined: 1-February 03
From: OC
Member No.: 219
Region Association: Southern California



remember...the motor expands....
User is offlineProfile CardPM
Go to the top of the page
+Quote Post

2 Pages V  1 2 >
Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 



- Lo-Fi Version Time is now: 31st October 2024 - 05:52 PM