 Overspray Removal from Fresh Air Inlet Box |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
  |
| DennisV |
  Nov 5 2025, 10:26 AM
Post
#1
|
|
Senior Member  Group: Members Posts: 787 Joined: 8-August 20 From: Santa Rosa, CA Member No.: 24,575 Region Association: Northern California 
 |
Does anyone have a tested method for removing paint from the fresh air inlet box? Ours had quite a bit of overspray on it. I tried:
* Acetone (had done great on everything else) * Goo-gone * Goof-off graffiti Ultimately made it way worse. (IMG:style_emoticons/default/sad.gif) I must have been very embarrassed by the result, as I didn't even take a picture. I'm not sure what this box is made of that is making this so problematic. Thanks. |
   |
 
|
| friethmiller |
Nov 5 2025, 10:40 AM
Post
#2
|
|
Senior Member Group: Members Posts: 1,083 Joined: 10-February 19 From: Austin, TX Member No.: 22,863 Region Association: Southwest Region
|
I used Lacquer Thinner.
|
 |
|
| Olympic 914 |
Nov 5 2025, 11:25 AM
Post
#3
|
|
Group: Members Posts: 1,763 Joined: 7-July 11 From: Pittsburgh PA Member No.: 13,287 Region Association: North East States
|
I had luck using Brasso.
A bit of scrubbing but didn't hurt the plastic at all. |
|
|
|
| slowrodent |
Nov 5 2025, 11:31 AM
Post
#4
|
|
Member Group: Members Posts: 214 Joined: 29-February 20 From: Tucson/Oro Valley Member No.: 23,981 Region Association: Southwest Region
|
Black spray paint (IMG:style_emoticons/default/smile.gif)
|
|
|
|
| IronHillRestorations |
Nov 5 2025, 11:47 AM
Post
#5
|
|
I. I. R. C. Group: Members Posts: 6,890 Joined: 18-March 03 From: West TN Member No.: 439 Region Association: None
|
+1 for just painting it black
|
|
|
|
| 914sgofast2 |
Nov 5 2025, 01:54 PM
Post
#6
|
|
Senior Member Group: Members Posts: 781 Joined: 10-May 13 From: El Dorado Hills, CA Member No.: 15,855 Region Association: None |
use some red rubbing compound and polish it off. The stuff is made for cutting down old oxidized paint.
|
|
|
|
| DennisV |
Nov 25 2025, 05:53 AM
Post
#7
|
|
Senior Member Group: Members Posts: 787 Joined: 8-August 20 From: Santa Rosa, CA Member No.: 24,575 Region Association: Northern California
|
Closing this out in case it might help someone else.
We also tried lacquer thinner, isopropyl alcohol. Just wasn't helping things. As a couple folks suggested, we ended up painting it. Used this flat black Krylon Fusion all-in-one paint and primer that says it will adhere to plastic. Initial results was a pretty good match. We'll see how well it wears. Thanks for the suggestions.  |
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 25th November 2025 - 12:17 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.