TPS Testing Options

[cabrioartie]

The car is a '74 2.0l, trying to fix all the items wrong after purchase.

Have found the following items bad and have replaced them:
- MPS
- AAR
- Decel Valve
- CHT
- Spark plugs and wires

I have a bogging/lack of power at about 3000 RPMs, I assumed it was the TPS. But, testing it with the 20 click method I get all 20 clicks consistently.

My question is, is this a valid test to ensure the TPS is good?

And if no, how else should I test it?

And if yes, what else could be wrong to cause the problem?

[bdstone914]

The car is a '74 2.0l, trying to fix all the items wrong after purchase.

Have found the following items bad and have replaced them:
- MPS
- AAR
- Decel Valve
- CHT
- Spark plugs and wires

I have a bogging/lack of power at about 3000 RPMs, I assumed it was the TPS. But, testing it with the 20 click method I get all 20 clicks consistently.

My question is, is this a valid test to ensure the TPS is good?

And if no, how else should I test it?

And if yes, what else could be wrong to cause the problem?

Pull the cover and inspect the traces on the circuit board. They can get worm. Sometins the arms can be bent to get the points to contact solid traces.

[emerygt350]

The clicks are a good method. If the TPS is shot you can get a complete cut at cruise or the loss of clicks. Is the bog you mention like a carb or does it feel like a complete engine wide miss?

[mgphoto]

The car is a '74 2.0l, trying to fix all the items wrong after purchase.

Have found the following items bad and have replaced them:
- MPS
- AAR
- Decel Valve
- CHT
- Spark plugs and wires

I have a bogging/lack of power at about 3000 RPMs, I assumed it was the TPS. But, testing it with the 20 click method I get all 20 clicks consistently.

My question is, is this a valid test to ensure the TPS is good?

And if no, how else should I test it?

And if yes, what else could be wrong to cause the problem?

I’ve found that the bog down at 3k is a distributor issue. Swooped in a 123 problem solved.

[cabrioartie]

The car is a '74 2.0l, trying to fix all the items wrong after purchase.

Have found the following items bad and have replaced them:
- MPS
- AAR
- Decel Valve
- CHT
- Spark plugs and wires

I have a bogging/lack of power at about 3000 RPMs, I assumed it was the TPS. But, testing it with the 20 click method I get all 20 clicks consistently.

My question is, is this a valid test to ensure the TPS is good?

And if no, how else should I test it?

And if yes, what else could be wrong to cause the problem?

Pull the cover and inspect the traces on the circuit board. They can get worm. Sometins the arms can be bent to get the points to contact solid traces.

Can the TPS cover be removed while the TPS is in the car? What would be the procedure?

[cabrioartie]

The clicks are a good method. If the TPS is shot you can get a complete cut at cruise or the loss of clicks. Is the bog you mention like a carb or does it feel like a complete engine wide miss?

Feels like a complete lack of power, and if I continue to push on the accelerator it eventually causes the car to jump forward/or feel like its accelerating, but it never feels like it has the proper power.

[cabrioartie]

The car is a '74 2.0l, trying to fix all the items wrong after purchase.

Have found the following items bad and have replaced them:
- MPS
- AAR
- Decel Valve
- CHT
- Spark plugs and wires

I have a bogging/lack of power at about 3000 RPMs, I assumed it was the TPS. But, testing it with the 20 click method I get all 20 clicks consistently.

My question is, is this a valid test to ensure the TPS is good?

And if no, how else should I test it?

And if yes, what else could be wrong to cause the problem?

I’ve found that the bog down at 3k is a distributor issue. Swooped in a 123 problem solved.

I actually purchased a 123 when I purchased the car, but I haven't thought about putting it in since I had so many other problems/failed components. I didn't want to change more than one thing at a time, but I've now replaced most of the failed items and could replace the distributor.

I was waiting on the 123 install until the car was running properly just in case the install didn't go well. Then I would know what was causing the problem.