Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

2 Pages V  1 2 >  
 Reply to this topicStart new topic
> No Fuel from Injectors, in crank mode
cary
post Jan 15 2006, 09:29 PM
Post #1


Advanced Member
****

Group: Members
Posts: 3,900
Joined: 26-January 04
From: Sherwood Oregon
Member No.: 1,608
Region Association: Pacific Northwest
We're still pulling our hair out. Took a perfectly running car. Pulled the engine to install a new muffler and straighten the front motor mount.

Now it won't start at times. Right now I have NO FUEL SPRAY from the injectors when we crank the ignition. It won't start like that. (IMG:http://www.914world.com/bbs2/html/emoticons/mad.gif)

Checked the valve adjustment, A-Ok.
Checked the ignition. All checked out, both HT & LT. We did have the ignition wire hooked to the (-) for a while.
But switching it back didn't help. Could that have burned up something I can't see ?
Fuel pressure perfect 29psi. Pumps 8 oz in 15 seconds.

Here's what I have now :

When you charge the ignition. One opposing pair of the injectors click. But a couple times. I got nothing. ZERO.
Then I unhook the harness to check the trigger points. I still get the click of the injectors with the harness unplugged. Is that right ?
So that leads me to test the harness to the ECU. All three (12, 21 & 22) test fine. Both continuity and signal. Still stumped. Tested the signal out of the trigger point connector. Fine on both sides.

Now I pull the injectors to test for spray. Nothing. I get a burst at the start. None during the cranking. Then a couple bursts when we turn the key off crank. That is screwed up. Pulled the plugs dry as a bone.

There has to be a simple answer. Its not that complex. But I'm missing something.

How come no spray at ignition crank ?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
boxstr
post Jan 15 2006, 09:31 PM
Post #2


MEMBER:PACIFIC NORTHWEST REGION
*****

Group: Members
Posts: 7,522
Joined: 25-December 02
From: OREGON
Member No.: 12
Region Association: Pacific Northwest
If your car has a bad injector resistor pack that would cause zero fuel at crank.Located over by the battery four wires out to one large plug. They are housed in a shiny aluminium housing.
CCLINNOGASNOGO
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
bd1308
post Jan 15 2006, 09:32 PM
Post #3


Sir Post-a-lot
*****

Group: Members
Posts: 8,020
Joined: 24-January 05
From: Louisville,KY
Member No.: 3,501
this is D-jet right?

b
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
cary
post Jan 15 2006, 09:37 PM
Post #4


Advanced Member
****

Group: Members
Posts: 3,900
Joined: 26-January 04
From: Sherwood Oregon
Member No.: 1,608
Region Association: Pacific Northwest
Sorry, 73 1.7 D-Jet.

Craig,

Where is it located ? I don't see anything different than my 74 2.0 D-Jet.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
bd1308
post Jan 15 2006, 09:40 PM
Post #5


Sir Post-a-lot
*****

Group: Members
Posts: 8,020
Joined: 24-January 05
From: Louisville,KY
Member No.: 3,501
scratch the resistor pack comment.

_Djet didnt have this.

but the "computer" (of sorts) is gettign power...so your not completly hosed.

are you getting a CONSTANT signal from the injector points?

did you check your injector grounds?

b
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
boxstr
post Jan 15 2006, 10:12 PM
Post #6


MEMBER:PACIFIC NORTHWEST REGION
*****

Group: Members
Posts: 7,522
Joined: 25-December 02
From: OREGON
Member No.: 12
Region Association: Pacific Northwest
Here is what one looks like.
CCLINSHOWME


Attached image(s)
Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
boxstr
post Jan 15 2006, 10:13 PM
Post #7


MEMBER:PACIFIC NORTHWEST REGION
*****

Group: Members
Posts: 7,522
Joined: 25-December 02
From: OREGON
Member No.: 12
Region Association: Pacific Northwest
Okay never mind.
CCLINOKAY
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
bd1308
post Jan 15 2006, 10:15 PM
Post #8


Sir Post-a-lot
*****

Group: Members
Posts: 8,020
Joined: 24-January 05
From: Louisville,KY
Member No.: 3,501
QUOTE (boxstr @ Jan 15 2006, 10:12 PM)
Here is what one looks like.
CCLINSHOWME

that resistor pack is not applicable to the D-jetronic injection system....

the positive power is actually supplied from the "ECU" and does not require a resistor pack like the L-jet does (which switches ground...)

b
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
cary
post Jan 15 2006, 11:57 PM
Post #9


Advanced Member
****

Group: Members
Posts: 3,900
Joined: 26-January 04
From: Sherwood Oregon
Member No.: 1,608
Region Association: Pacific Northwest
Beats the s*** out of me.

Went back after dinner. Tested the MPS for vacuum. Failed the test. Sank to 10inches in 15 minutes. Bench tested the 2nd one, it failed too. Bench tested the 3rd. one. Held fine. All three, the coils tested ok.

Put in the good one and it started right up. Tested it about ten times. Started fine. We'll see in the am.

It doesn't give me much confidence. I like black & white. Not hazy grey. (IMG:http://www.914world.com/bbs2/html/emoticons/wacko.gif)

Still has a waver at high RPM's. More than a flat spot. I have a rebuilt Cardone dizzy coming from NAPA. It may clear up all kinds of things.

Thanks for the encouragement.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
cary
post Jan 16 2006, 08:39 AM
Post #10


Advanced Member
****

Group: Members
Posts: 3,900
Joined: 26-January 04
From: Sherwood Oregon
Member No.: 1,608
Region Association: Pacific Northwest
Well its a new day. Went out this am to start it. Started, but only ran for 10 seconds then stopped. Not to start again. Now what ?
Same as yesterday. Something is shorted. Has to be.

I'm going to test and look at the CHT. That wire is down by the MPS. Your guys thoughts ?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
DNHunt
post Jan 16 2006, 08:55 AM
Post #11


914 Wizard? No way. I got too much to learn.
****

Group: Members
Posts: 4,099
Joined: 21-April 03
From: Gig Harbor, WA
Member No.: 598
Cary

A bad CHT will keep the car from starting but, I believe it's because it floods not from being lean. I imagine you have thought of this already but check all the connectors and grounds (especially grounds). If I remember there should be a constant ~ 12v which you should be able to measure available at the injectors and the FI switches the ground. It may be wothwhile testing the resistance in the harness also. The insulation on 30 year old wires gets awfully hard and can crack.

The fact that you were able to see some improvement after replacing the MPS makes me suspect connections on that side of the engine. In messing with my car I have found that the connectors at the injectors can become loose with thw D-jet style connectors. I've had to give the females on the harnessa gentle squeeze to close them a little and I've cleaned them to bright metal.

Dave
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
cary
post Jan 16 2006, 11:06 AM
Post #12


Advanced Member
****

Group: Members
Posts: 3,900
Joined: 26-January 04
From: Sherwood Oregon
Member No.: 1,608
Region Association: Pacific Northwest
Dave, your right. Backwards. The CHT would give extra fuel. Tested the CHT 4050 ohms at the heated shop temp of 52. So its right on target.

We pulled the ground spade and cleaned all the connections. But I think its still a short somewhere around the MPS. But why only when the block is cold ?

If all the injectors click when you power the ignition. Why do they not get fuel ? If the grounds where bad. I would think that I wouldn't get a click at all.
But this am I didn't listen for the click. Hummmm.

I may pull the entire harness and wiggle test every wire in the harness.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
bd1308
post Jan 16 2006, 11:11 AM
Post #13


Sir Post-a-lot
*****

Group: Members
Posts: 8,020
Joined: 24-January 05
From: Louisville,KY
Member No.: 3,501
maybe its time to get the harness rebuilt?


b
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
cary
post Jan 16 2006, 11:18 AM
Post #14


Advanced Member
****

Group: Members
Posts: 3,900
Joined: 26-January 04
From: Sherwood Oregon
Member No.: 1,608
Region Association: Pacific Northwest
I'm thinking the same thing. I was just away at Jeff's sight.

I'm think I'm going to drop the engine again at take the harness out and test it. My Super In Law is at home still working on it. But he's getting a little worn out. Plus he wants to get finished on taking the engine out of the parts car. So we can flip it over and pull the suspension off. Thats a lot more fun than cussing at a car that won't talk back.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
DNHunt
post Jan 16 2006, 11:56 AM
Post #15


914 Wizard? No way. I got too much to learn.
****

Group: Members
Posts: 4,099
Joined: 21-April 03
From: Gig Harbor, WA
Member No.: 598
Wait a minute. I don't think i understood. Are you saying all of the injectors open? If so then there are a couple of possibilities. One is fuel delivery. What is the fuel pressure? Fuel may not be getting to the injectors so check the fuel pressure regulator with a gauge, fuel pump, fuel filter, sock in the fuel tank. Second possibility is electrical if fuel is getting to the injectors at the correct pressure.

These are peak and hold injectors so full current opens them and it is reduced to hold them open. Check the resistance in the harness. They may be openning and then not have enough current to hold them open so the pulsewidth is too short. The injectors maybe failing. Swap them to the other side and see if the problem follows them.

Good luck

Dave
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
2-OH!
post Jan 16 2006, 02:07 PM
Post #16


Senior Member
***

Group: Members
Posts: 552
Joined: 17-October 03
From: Santa Clarita, Kalifornication
Member No.: 1,253
Broken wire/connection at the injector connector(s)...You banged it on the sheet metal when you droped or replaced the engine...Breaks off right behind the metal contact in the connector...Hard to see but it sounds like you get it pretty close to contact and the start the engine, vibration breaks the contact again and you lose injector..

I will not admit to how I know this problem...

2-OH!
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
dlo914
post Jan 16 2006, 02:15 PM
Post #17


Whatchu' lookin' at?!?!
****

Group: Members
Posts: 3,433
Joined: 6-September 04
From: San Gabriel, CA
Member No.: 2,697
QUOTE (boxstr @ Jan 15 2006, 08:12 PM)
Here is what one looks like.
CCLINSHOWME

what FI system did this come off of?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
dlo914
post Jan 16 2006, 02:17 PM
Post #18


Whatchu' lookin' at?!?!
****

Group: Members
Posts: 3,433
Joined: 6-September 04
From: San Gabriel, CA
Member No.: 2,697
QUOTE (boxstr @ Jan 15 2006, 08:12 PM)
Here is what one looks like.
CCLINSHOWME

could i see the topside?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
boxstr
post Jan 16 2006, 02:19 PM
Post #19


MEMBER:PACIFIC NORTHWEST REGION
*****

Group: Members
Posts: 7,522
Joined: 25-December 02
From: OREGON
Member No.: 12
Region Association: Pacific Northwest
The one on the left.


Attached image(s)
Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
bd1308
post Jan 16 2006, 02:43 PM
Post #20


Sir Post-a-lot
*****

Group: Members
Posts: 8,020
Joined: 24-January 05
From: Louisville,KY
Member No.: 3,501
dlo, this is what I owe you...i'm working on it for you.

b
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
« Next Oldest · 914World Garage · Next Newest »
 

2 Pages V  1 2 >
Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 

Display Mode: Standard · Switch to: Linear+ · Switch to: Outline

Track this topic · Email this topic · Print this topic · Subscribe to this forum

- Lo-Fi Version Time is now: 9th May 2025 - 05:28 PM
Invision Power Board v9.1.4 © 2025  IPS, Inc.
All rights reserved 914World.com © since 2002
914World.com is the fastest growing online 914 community!
We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ...