 Quickie Lub on a Gas Pedal |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
  |
| swm914 |
 Mar 13 2007, 04:27 PM
Post
#1
|
|
Member  Group: Members Posts: 82 Joined: 28-January 07 From: Palmyra, PA Member No.: 7,484 Region Association: None  |
Anything like a quickie lub on a 914 gas pedal? I'm new to 914 mechanicals. The gas pedal on my '74 is way too stiff. Is there a quick way to lub the gas pedal mechanism until I have the time to figure out how and what tear apart to do it right and/or replace anything? Thanks
Steve |
   |
 
|
| Rough_Rider |
Mar 13 2007, 06:03 PM
Post
#2
|
|
Smurf Zone Group: Members Posts: 525 Joined: 16-August 04 From: Beaverton, OR Member No.: 2,547 |
which motor have you got is it carbed or FI?
Could be you've just got a sticky cable which might be cured party by spraying a little light lube down there. Do NOT use WD40. If you can pull the cable off throttle linkage & pull that cable then with a helper have them depress acc pedal. Could be a simple cable replace. |
|
|
|
| So.Cal.914 |
Mar 13 2007, 06:39 PM
Post
#3
|
|
"...And it has a front trunk too." Group: Members Posts: 6,588 Joined: 15-February 04 From: Low Desert, CA./ Hills of N.J. Member No.: 1,658 Region Association: None |
On the back of the gas pedal there is a cup that the linkage rod 'pops' into.
I have had it dry out so much that it was sticking a little. Pull on the pedal until it pops out and put a little LUBE in there. |
|
|
|
| swm914 |
Mar 13 2007, 07:38 PM
Post
#4
|
|
Member Group: Members Posts: 82 Joined: 28-January 07 From: Palmyra, PA Member No.: 7,484 Region Association: None |
QUOTE(Rough_Rider @ Mar 13 2007, 04:03 PM)  which motor have you got is it carbed or FI? Could be you've just got a sticky cable which might be cured party by spraying a little light lube down there. Do NOT use WD40. If you can pull the cable off throttle linkage & pull that cable then with a helper have them depress acc pedal. Could be a simple cable replace. I have a 2.0 FI. What kind of lube is good to use? Thanks |
|
|
|
| So.Cal.914 |
Mar 13 2007, 07:41 PM
Post
#5
|
|
"...And it has a front trunk too." Group: Members Posts: 6,588 Joined: 15-February 04 From: Low Desert, CA./ Hills of N.J. Member No.: 1,658 Region Association: None |
Silicone spray works well.
|
|
|
|
| URY914 |
Mar 13 2007, 08:42 PM
Post
#6
|
|
I built the lightest 914 in the history of mankind. Group: Members Posts: 126,350 Joined: 3-February 03 From: Jacksonville, FL Member No.: 222 Region Association: None |
Your problem is not the pedal it's the cable. You may have a few strands broken and it is binding up.
Replace the cable. (IMG:style_emoticons/default/biggrin.gif) |
|
|
|
| alremley |
Mar 13 2007, 09:16 PM
Post
#7
|
|
Newbie Group: Members Posts: 32 Joined: 25-September 05 From: Lancaster, KY Member No.: 4,861 |
QUOTE(swm914 @ Mar 13 2007, 02:27 PM) Anything like a quickie lub on a 914 gas pedal? I'm new to 914 mechanicals. The gas pedal on my '74 is way too stiff. Is there a quick way to lub the gas pedal mechanism until I have the time to figure out how and what tear apart to do it right and/or replace anything? Thanks Steve Stiff or sticking petal, usually comes down to a worn petal assembly, the bearings are toast, and or plastic inside the cable is worn and broken. I should know. I have had both problems. The cable should never need lubing. You also want to check the petal push rod to be sure it is not bent. (IMG:style_emoticons/default/driving.gif) |
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 03:36 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.