 Camp lenses help, Craig...explain please |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| r_towle |
 May 2 2004, 06:59 PM
Post
#1
|
|
Custom Member  Group: Members Posts: 24,705 Joined: 9-January 03 From: Taxachusetts Member No.: 124 Region Association: North East States 
 |
There does not seem to be a slot for the long wire to go through per the instructions.....
Do I drill one??? Yup, takes me a while to do things... Rich |
   |
 
|
  |
Replies(1 - 7)
| Bleyseng |
May 2 2004, 07:17 PM
Post
#2
|
|
Aircooled Baby! Group: Members Posts: 13,036 Joined: 27-December 02 From: Seattle, Washington (for now) Member No.: 24 Region Association: Pacific Northwest |
Yeah, its there....its just really small.
Look again Geoff |
|
|
|
| r_towle |
May 2 2004, 07:27 PM
Post
#3
|
|
Custom Member Group: Members Posts: 24,705 Joined: 9-January 03 From: Taxachusetts Member No.: 124 Region Association: North East States
|
I see the slot from the inside/front....but I do not see it going all the way through...It looks like it goes into the large round part in the back...
Do I take off the plastic piece..or just try shoving the wire through and see where it comes out... Dont reall want to take off the plastic piece..looks like it wont survive it. |
|
|
|
| Bleyseng |
May 2 2004, 07:29 PM
Post
#4
|
|
Aircooled Baby! Group: Members Posts: 13,036 Joined: 27-December 02 From: Seattle, Washington (for now) Member No.: 24 Region Association: Pacific Northwest |
IIRC just shove the wire thru, don't take it apart!
|
|
|
|
| djm914-6 |
May 2 2004, 07:38 PM
Post
#5
|
|
Happiness is: Getting on the road Group: Members Posts: 1,864 Joined: 6-February 03 From: Burlington MA Member No.: 248 Region Association: None |
Yup, just shove it through. IIRC, mine was a bit tight too, but then again, I added several coats of reflective silver to the housing.
|
|
|
|
| r_towle |
May 2 2004, 07:38 PM
Post
#6
|
|
Custom Member Group: Members Posts: 24,705 Joined: 9-January 03 From: Taxachusetts Member No.: 124 Region Association: North East States
|
thanx...i'll save it for tommorow
I just bought a race car over the winter....so I have decided to keep this one and drive it for fun...now the list of things that I overlooked and ignored was huge... No headlights Brake lights were a mess No reverse lights No driving lights No carpets Interior from hell (Of course I sold alot of interior stuff cause I am a short sighted bonehead) The list keeps getting longer... These lights are part of the front end lighting rebuild, did the rear end earlier today. Also had to re-adjust the suspension...it was on the bottom slot of my bilsteins...nice and low for the 50s...now I had to move all that up for street tires and it really is nice not having to drive up on a board to get the jack under it...I forgot how easy it should be. Rich |
|
|
|
| boxstr |
May 2 2004, 08:45 PM
Post
#7
|
|
MEMBER:PACIFIC NORTHWEST REGION Group: Members Posts: 7,522 Joined: 25-December 02 From: OREGON Member No.: 12 Region Association: Pacific Northwest |
Rich, After you have the light bulb out, you can look and see the holes, Use the larger of the two, don't worry it will go through.
CCLINHAIRAROUNDTHEHOLE |
|
|
|
| Eric_Shea |
May 2 2004, 09:29 PM
Post
#8
|
|
PMB Performance Group: Admin Posts: 19,304 Joined: 3-September 03 From: Salt Lake City, UT Member No.: 1,110 Region Association: Rocky Mountains  |
Rich,
Click Here The photos show where the wire comes out in the back and how it's routed in the housing. Hope that helps, E. |
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 19th July 2025 - 09:01 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.