 Restoring sail panel trim, They're done! |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| PanelBilly |
 Nov 10 2013, 09:28 PM
Post
#1
|
|
914 Guru  Group: Members Posts: 5,881 Joined: 23-July 06 From: Kent, Wa Member No.: 6,488 Region Association: Pacific Northwest 
 |
I decided I might as well fix the trim that came with my car because I wasn't going to be able to afford a set that looked like new. First i used a baggie of sand and a small hammer to straighten it and press out the dents
 Then I got out the sand paper and took off the finish while sanding down the high spots  Finished product is still a little rough, but the basic shape is correct now.  I'm going to see if i can get the parts painted with Spectrachrome as there's a wheel repair shop close to me that works with the stuff. I saw a demo of the product on one of Jay Leno's videos and it looked good. I know I'll have a chrome part rather than a polished aluminum, but the car is far from stock now and I want a clean look |
   |
 
|
  |
Replies(1 - 11)
| Jones Geraint |
Nov 10 2013, 09:52 PM
Post
#2
|
|
Newbie Group: Members Posts: 1 Joined: 10-November 13 From: china Member No.: 16,630 Region Association: France |
The rear seat area gets assembled starting with the sail panel trim brackets (6) and then the package tray reenforcement (Walkera RC Hélicoptère). The hard ware should be kept slightly loose until all the parts have been fitted. Note: All of these parts are painted semi-flat black.
|
|
|
|
| PanelBilly |
Nov 10 2013, 11:02 PM
Post
#3
|
|
914 Guru Group: Members Posts: 5,881 Joined: 23-July 06 From: Kent, Wa Member No.: 6,488 Region Association: Pacific Northwest
|
I think I just entered the Twilight Zone.
|
|
|
|
| r_towle |
Nov 10 2013, 11:07 PM
Post
#4
|
|
Custom Member Group: Members Posts: 24,705 Joined: 9-January 03 From: Taxachusetts Member No.: 124 Region Association: North East States
|
What, you don't have those parts?
Glad to hear you are painting the metalwork....I would have expected nothing less cool. Please show us how it works out. If not, buff them to a polish and put some clear on it. |
|
|
|
| PanelBilly |
Aug 25 2014, 05:26 PM
Post
#5
|
|
914 Guru Group: Members Posts: 5,881 Joined: 23-July 06 From: Kent, Wa Member No.: 6,488 Region Association: Pacific Northwest
|
After months and months of stopping by the shop that was doing the chrome paint, I finely gave up and said "give me back my stuff!" The guy kept doing it over and over. Every time it came out crappy. Looked bumpy, clearcoat yellowed, clearcoat pealed off. The guy agreed to sand off all the layers of chrome and primer and buff the aluminum, but after a few weeks, I said I wanted it back in the half sanded condition they are in.
I went to the powder coater, who sent me to a guy who polishes who said I need to send the stuff to a guy in So. El Monte! The story is that THIS guy knows his shit. I called him and he appeared knowledgeable about how our targa trim was originally made and how he could make it right again. So I'm boxing up the stuff and sending it down to him for a look. Damn, I started this last November. That was before I took the engine in. |
|
|
|
| PanelBilly |
Oct 19 2014, 11:51 AM
Post
#6
|
|
914 Guru Group: Members Posts: 5,881 Joined: 23-July 06 From: Kent, Wa Member No.: 6,488 Region Association: Pacific Northwest
|
Got a call on Friday and the parts are complete and being shipped back. Cost including shipping back was $240. Sounds reasonable for the three parts if they look original
|
|
|
|
| PanelBilly |
Oct 30 2014, 09:27 PM
Post
#7
|
|
914 Guru Group: Members Posts: 5,881 Joined: 23-July 06 From: Kent, Wa Member No.: 6,488 Region Association: Pacific Northwest
|
The trim arrive today. Not as good as a new set, but the finish is pretty good. The coating doesn't cover up and of the minor defects in the metal and the metal was too thin to sand anymore.
  |
|
|
|
| boxsterfan |
Nov 1 2014, 11:20 PM
Post
#8
|
|
914's are kewl Group: Members Posts: 1,776 Joined: 6-June 03 From: San Ramon, CA Member No.: 791 Region Association: Northern California |
I plan to take all that sail panel vinyl off and those bits you have been struggling with and make a brushed aluminum "cap" for my 914 some day ala a 911 Targa.
Attached image(s) 
|
|
|
|
| e_artiles |
Nov 1 2014, 11:43 PM
Post
#9
|
|
Member Group: Members Posts: 76 Joined: 14-February 12 From: Corona, CA Member No.: 14,131 Region Association: Southern California |
I need my trim pieces done. What's the name and address of the shop in El Monte?
|
|
|
|
| r_towle |
Nov 2 2014, 02:44 PM
Post
#10
|
|
Custom Member Group: Members Posts: 24,705 Joined: 9-January 03 From: Taxachusetts Member No.: 124 Region Association: North East States
|
QUOTE(boxsterfan @ Nov 2 2014, 01:20 AM)  I plan to take all that sail panel vinyl off and those bits you have been struggling with and make a brushed aluminum "cap" for my 914 some day ala a 911 Targa. Is that aluminum or stainless? |
|
|
|
| Mikey914 |
Nov 2 2014, 03:00 PM
Post
#11
|
|
The rubber man Group: Members Posts: 12,767 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None
|
Pretty sure the 911 was stainless as aluminum is very soft, and will scratch easily.
|
|
|
|
| 914Sixer |
Nov 2 2014, 06:36 PM
Post
#12
|
|
914 Guru Group: Members Posts: 9,123 Joined: 17-January 05 From: San Angelo Texas Member No.: 3,457 Region Association: Southwest Region
|
Mark is right, 911 stuff is stainless.
|
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 04:54 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.