 made some progress |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| grasshopper |
 Apr 30 2005, 09:00 PM
Post
#1
|
|
Advanced Member  Group: Members Posts: 2,613 Joined: 10-December 04 From: Valdosta, GA Member No.: 3,258 Region Association: None  |
well right before WCC, i started poking around in the engine compartment and found a shit load of bondo in there covering up a rust HOLE. the weird thing about my car though, is that the PO made a home made battery tray and moved it back about 4-5 inches, so it didnt rust out the hell hole, but umm the place in front of it. (IMG:http://www.914world.com/bbs2/html/emoticons/biggrin.gif) heres when I removed the bondo
Attached image(s) 
|
   |
 
|
  |
Replies(1 - 5)
| grasshopper |
Apr 30 2005, 09:01 PM
Post
#2
|
|
Advanced Member Group: Members Posts: 2,613 Joined: 10-December 04 From: Valdosta, GA Member No.: 3,258 Region Association: None |
heres when i removed it, and yes i fixed up the other rust too, it was just surface rust except for on little hole.
Attached image(s) 
|
|
|
|
| grasshopper |
Apr 30 2005, 09:02 PM
Post
#3
|
|
Advanced Member Group: Members Posts: 2,613 Joined: 10-December 04 From: Valdosta, GA Member No.: 3,258 Region Association: None |
heres the new piece i made
Attached image(s) 
|
|
|
|
| grasshopper |
Apr 30 2005, 09:03 PM
Post
#4
|
|
Advanced Member Group: Members Posts: 2,613 Joined: 10-December 04 From: Valdosta, GA Member No.: 3,258 Region Association: None |
drilled the holes
Attached image(s) 
|
|
|
|
| grasshopper |
Apr 30 2005, 09:04 PM
Post
#5
|
|
Advanced Member Group: Members Posts: 2,613 Joined: 10-December 04 From: Valdosta, GA Member No.: 3,258 Region Association: None |
test fitting, and yes i did take a grinder to the welds. I will post a pic of the welded in piece in the morning. oh yea, i finally got the engine back in after about 6 months. (IMG:http://www.914world.com/bbs2/html/emoticons/biggrin.gif)
Attached image(s) 
|
|
|
|
| Qarl |
Apr 30 2005, 09:08 PM
Post
#6
|
|
Shriveled member Group: Benefactors Posts: 5,233 Joined: 8-February 03 From: Florida Member No.: 271 Region Association: None  |
I think you might wanna try some stronger tape... it will eventually fall off!
Just kidding! (IMG:http://www.914world.com/bbs2/html/emoticons/smilie_pokal.gif) (IMG:http://www.914world.com/bbs2/html/emoticons/smilie_pokal.gif) (IMG:http://www.914world.com/bbs2/html/emoticons/smilie_pokal.gif) (IMG:http://www.914world.com/bbs2/html/emoticons/smilie_pokal.gif) Great job! |
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 1st June 2024 - 05:13 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.