Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

> trailing arm bushings, How to remove?
Qarl
post Aug 24 2003, 05:29 PM
Post #1


Shriveled member
*****

Group: Benefactors
Posts: 5,233
Joined: 8-February 03
From: Florida
Member No.: 271
Region Association: None
Okay... I spent the weekend disassembly the rear suspension.

Oh yeah, my suspension was all off the car.

F-ING CASTELATED NUTS!!!!! It took quite a few sessions with a propane torch and a high-torque impact wrench on max setting to remove each one.

It's real fun removing this nut without the car mounted to anything. The hub and axle just rotate away!!!

I ended up placing the hub (still mounted on the trailing arm with the axle attached into a vise on my bench). I tried removing it with a socket extension and 24" breaker bar. No such luck. The heat and impact wrench worked after many repeated attempts. My teeth are sore from clamping down.

Okay.. so now I just have to remove the hub and bearings. No problem.

What about the bushings? I plan on installing Muellers needle bearings in the rear, but I have no idea how to get the old stuff out.

Any advice?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
 
 Reply to this topicStart new topic
Replies(1 - 14)
Brad Roberts
post Aug 24 2003, 05:34 PM
Post #2


914 Freak!
***************

Group: Members
Posts: 19,148
Joined: 23-December 02
Member No.: 8
Region Association: None
Press. Or its a mess with propane torch/burning them out...

It takes 10 minutes per side with a press. Your going to need the press to install Muellers new tube anyway (hammer can be used.. but it screws up the end of the tube)


B
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Qarl
post Aug 24 2003, 05:39 PM
Post #3


Shriveled member
*****

Group: Benefactors
Posts: 5,233
Joined: 8-February 03
From: Florida
Member No.: 271
Region Association: None
Since, I don't have a press... just find a shop and tell them to press the rods out?

Any "special instructions" to tell them?


Attached image(s)
Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Brad Roberts
post Aug 24 2003, 05:42 PM
Post #4


914 Freak!
***************

Group: Members
Posts: 19,148
Joined: 23-December 02
Member No.: 8
Region Association: None
Not really.. just ask them to press them out.

You dont have a "mechanics shop" that you work with on this crap ??

B
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Charles Deutsch
post Aug 24 2003, 05:43 PM
Post #5


Unregistered
QUOTE(kellzey @ Aug 24 2003, 03:29 PM)

F-ING CASTELATED NUTS!!!!!  It took quite a few sessions with a propane torch and a high-torque impact wrench on max setting to remove each one.


I ended up placing the hub (still mounted on the trailing arm with the axle attached into a vise on my bench).  I tried removing it with a socket extension and 24" breaker bar.  No such luck.  The heat and impact wrench worked after many repeated attempts.  My teeth are sore from clamping down.


I did not want to hear that. I'll probably give myself a hernia.

Charles
Go to the top of the page
+Quote Post
URY914
post Aug 24 2003, 07:17 PM
Post #6


I built the lightest 914 in the history of mankind.
****************************************************************************************************

Group: Members
Posts: 120,883
Joined: 3-February 03
From: Jacksonville, FL
Member No.: 222
Region Association: None
I took a hammer (BFH) and beat the shit of of them to get 'em out. Took days.

Take 'em to a shop.

Paul
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
fiid
post Aug 24 2003, 07:20 PM
Post #7


Turbo Megasquirted Subaru Member
****

Group: Members
Posts: 2,827
Joined: 7-April 03
From: San Francisco, CA
Member No.: 530
Region Association: Northern California
Heres how I did it:

Get the trailing arm on a bench with the buskings in vertical orientation and dso they are haning off the edge of said bench. Have a helper hold the hub end of something.

Take a blow torch. Light it, and get it running extremely hot. Heat the bushing tube at both ends. You have things close to hot enough when the busing flashes and catches fire. Then hit the threaded bar (sticking out of the bushings) with a plastic mallet or a hammer (protect the threads with a bit of wood). Repeat until the bar drops out. You should then be able to take a bar or something and hammer the two busings out from the opposite sides.

This method stinks like a mo-fo, but it does work. Don't be afraid of the rubber cathing fire - it really doesn't burn very well.

Take all the usual precautions you should take when using a blow torch.

Fiid.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
URY914
post Aug 24 2003, 07:49 PM
Post #8


I built the lightest 914 in the history of mankind.
****************************************************************************************************

Group: Members
Posts: 120,883
Joined: 3-February 03
From: Jacksonville, FL
Member No.: 222
Region Association: None
Invite Jenna Jamison over...
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
vortrex
post Aug 24 2003, 08:30 PM
Post #9


Senior Member
***

Group: Members
Posts: 1,687
Joined: 24-December 02
From: SF, CA
Member No.: 4
Region Association: None
burned mine out in less than 20 min each. get them really hot and take a screwdriver to it. work at puncturing straight through in one spot and then the rest is easy.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Qarl
post Aug 24 2003, 08:58 PM
Post #10


Shriveled member
*****

Group: Benefactors
Posts: 5,233
Joined: 8-February 03
From: Florida
Member No.: 271
Region Association: None
Did you puncture through the rubber or just whack the metal shaft?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
J P Stein
post Aug 24 2003, 09:43 PM
Post #11


Irrelevant old fart
*****

Group: Members
Posts: 8,797
Joined: 30-December 02
From: Vancouver, WA
Member No.: 45
Region Association: None
Fire is gud.

Protect the threads & whack the mofoin' shaft.

I have found it easiest to cut off the rubber bushing flange first.

Who's Jenna Jaminson? (IMG:style_emoticons/default/cool_shades.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
vortrex
post Aug 24 2003, 09:44 PM
Post #12


Senior Member
***

Group: Members
Posts: 1,687
Joined: 24-December 02
From: SF, CA
Member No.: 4
Region Association: None
puncture through the rubber.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Scott Carlberg
post Aug 25 2003, 03:32 AM
Post #13


Porsche MOTORSPORTS
***

Group: Members
Posts: 1,595
Joined: 17-April 03
From: Modesto, Ca
Member No.: 580
QUOTE(kellzey @ Aug 24 2003, 04:29 PM)
Okay.. so now I just have to remove the hub and bearings. No problem.

What about the bushings? I plan on installing Muellers needle bearings in the rear, but I have no idea how to get the old stuff out.

Any advice?

Karl,
when Mueller changed my Bushings last weekend, he used a Press that he bought
from Harbour Freight.

IIRC, Mike said it was $60.00

Good luck with the bushings.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Brad Roberts
post Aug 25 2003, 09:16 AM
Post #14


914 Freak!
***************

Group: Members
Posts: 19,148
Joined: 23-December 02
Member No.: 8
Region Association: None
FYI:

Protect the threads on the shaft (if you plan to keep the shafts) with a steel 911 lug nut when your smacking the end with a hammer.

I know Karl wont be reusing his shafts.... but I thought everyone should know... dont F-up the threads. You will hate life.

Which is why I dont hammer on the shafts...



B
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
tryan
post Aug 25 2003, 10:37 AM
Post #15


Senior Member
***

Group: Members
Posts: 553
Joined: 22-January 03
From: smokey mountains gatlinburg tn
Member No.: 184
a three arm gear puller and a bunch-o-sockets worked well on the teener to get the shaft and bushings out. a hammer just bounced and was fruitless.

mapp gas was the tool of choice on the 911, but i was trying to avoid that smell.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
« Next Oldest · 914World Garage · Next Newest »
 

Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 

Display Mode: Switch to: Standard · Linear+ · Switch to: Outline

Track this topic · Email this topic · Print this topic · Subscribe to this forum

- Lo-Fi Version Time is now: 28th May 2024 - 08:58 PM
Invision Power Board v9.1.4 © 2024  IPS, Inc.
All rights reserved 914World.com © since 2002
914World.com is the fastest growing online 914 community!
We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ...