Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

> Voltage drop when I hit the brakes
PinetreePorsche
post Jan 10 2007, 08:03 AM
Post #1


Member
**

Group: Members
Posts: 235
Joined: 14-November 05
From: Falls Church, VA
Member No.: 5,124



What's wrong here? The voltage on my meter (stock- center console) falls from near 13 to 11-and-a-bit, daytime, and has a corresponding drop from a slightly lower starting (mid-12 area) with the lights on. Turning on the lights, without other loads, barely deflects the needle down, maybe .3 volts--that's for 2 fr. corner, two taillights and two markers. Why would the brake bulbs drain so much more? -is there a short somewhere--and no, I haven't been blowing any fuses. Just wondered--don't want to get stuck in an after-dark traffic jam, sit with the brakes on and drain the battery. -C
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
 
Reply to this topicStart new topic
Replies(1 - 13)
Dr. Roger
post Jan 10 2007, 08:10 AM
Post #2


A bat out of hell.
****

Group: Members
Posts: 3,944
Joined: 31-January 05
From: Hercules, California
Member No.: 3,533
Region Association: Northern California



if all of your connectors are clean and wiring is healthy, then i'd load test your battery to verify it's health.

everyone says, "ohhhh, my battery is only X years old..."

whatever. load testers are cheap easy insurance for your battery. and you'll drive with a bit more confidence and probably save one AAA use. =-)

Roger (IMG:style_emoticons/default/beerchug.gif) Good luck.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
PinetreePorsche
post Jan 10 2007, 08:24 AM
Post #3


Member
**

Group: Members
Posts: 235
Joined: 14-November 05
From: Falls Church, VA
Member No.: 5,124



I'll check the battery--but that doesn't answer why so little voltage drop with the first position of the lights in the on position --and I might add, not much more drop when the fog/driving lamps are on as well, or enen (a bit more drop, but not much) when the headlights are on. Just the brakes draw it down a lot. -C
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
VaccaRabite
post Jan 10 2007, 08:30 AM
Post #4


En Garde!
**********

Group: Admin
Posts: 13,584
Joined: 15-December 03
From: Dallastown, PA
Member No.: 1,435
Region Association: MidAtlantic Region



Check your wiring first. Make sure that the connectors arn't all rusted, etc. More resistance = more load = more heat and could eventually lead to burned wires.

Zach
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
pfierb
post Jan 10 2007, 08:48 AM
Post #5


oldest member
***

Group: Members
Posts: 606
Joined: 1-May 05
From: The sign of good government in Connecticut is to keep raising taxes
Member No.: 4,008



QUOTE(PinetreePorsche @ Jan 10 2007, 09:03 AM) *

What's wrong here? The voltage on my meter (stock- center console) falls from near 13 to 11-and-a-bit, daytime, and has a corresponding drop from a slightly lower starting (mid-12 area) with the lights on. Turning on the lights, without other loads, barely deflects the needle down, maybe .3 volts--that's for 2 fr. corner, two taillights and two markers. Why would the brake bulbs drain so much more? -is there a short somewhere--and no, I haven't been blowing any fuses. Just wondered--don't want to get stuck in an after-dark traffic jam, sit with the brakes on and drain the battery. -C



Mine seems to do the same thing and the battery is new.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
dr914@autoatlanta.com
post Jan 10 2007, 09:20 AM
Post #6


914 Guru
*****

Group: Members
Posts: 8,092
Joined: 3-January 07
From: atlanta georgia
Member No.: 7,418
Region Association: None



No reason to check ANYTHING! This is typical for 914! The volt meter is wired in the same circuit as the brake light switch and we all know how much power two brake light bulbs take to operate! This is one of the tech tips in the Tech Tips 700!! Typical 914 (we love their little quirks!)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Dave_Darling
post Jan 10 2007, 09:52 AM
Post #7


914 Idiot
***************

Group: Members
Posts: 15,051
Joined: 9-January 03
From: Silicon Valley / Kailua-Kona
Member No.: 121
Region Association: Northern California



As I always tell people, the voltmeter is there "strictly for entertainment". It even jumps around when you have your turn signals on, which makes me snicker.

If you want an actual indication of the health of your charging system, you need to measure with a decent voltmeter directly across the battery posts. Not the clamps, the posts themselves.

Once you get to know what your stock VM does under different conditions, you may be able to use it to know when a light bulb has burned out. Apart from that, it's pretty useless...

--DD
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
robby750
post Jan 10 2007, 10:08 AM
Post #8


Senior Member
***

Group: Members
Posts: 646
Joined: 6-April 03
From: Lexington, Ky
Member No.: 521
Region Association: South East States



QUOTE(dr914@autoatlanta.com @ Jan 10 2007, 10:20 AM) *

No reason to check ANYTHING! This is typical for 914! The volt meter is wired in the same circuit as the brake light switch and we all know how much power two brake light bulbs take to operate! This is one of the tech tips in the Tech Tips 700!! Typical 914 (we love their little quirks!)

I have to agree here. Mine does the same thing and I used to worry about it all the time. After never having a charging problem, I just learned to ignore it.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
PinetreePorsche
post Jan 10 2007, 11:36 AM
Post #9


Member
**

Group: Members
Posts: 235
Joined: 14-November 05
From: Falls Church, VA
Member No.: 5,124



QUOTE(dr914@autoatlanta.com @ Jan 10 2007, 07:20 AM) *

No reason to check ANYTHING! This is typical for 914! The volt meter is wired in the same circuit as the brake light switch and we all know how much power two brake light bulbs take to operate! This is one of the tech tips in the Tech Tips 700!! Typical 914 (we love their little quirks!)


Thanks, George. I read the book, cover to cover, in two straight stints while I was waiting to see if they would call me in as a substitute for jury duty (they never did). Guess I should go back and take another look at the ones I flagged or earmarked as important--I'd probably retain more w/a second reading.
So, good doctor, is there any modification to the hook-up that would render the gauge more accurate/useful?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Brando
post Jan 10 2007, 11:52 AM
Post #10


BUY MY SPARE KIDNEY!!!
****

Group: Members
Posts: 3,935
Joined: 29-August 04
From: Santa Ana, CA
Member No.: 2,648
Region Association: Southern California



Yeah... if it were run between the voltage regulator positive and battery negative (or engine ground). That would give an accurate reading of your voltage output.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
PinetreePorsche
post Jan 10 2007, 09:46 PM
Post #11


Member
**

Group: Members
Posts: 235
Joined: 14-November 05
From: Falls Church, VA
Member No.: 5,124



QUOTE(Brando @ Jan 10 2007, 09:52 AM) *

Yeah... if it were run between the voltage regulator positive and battery negative (or engine ground). That would give an accurate reading of your voltage output.


Any downside to that? Do others do this modification?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
ClayPerrine
post Jan 10 2007, 09:51 PM
Post #12


Life's been good to me so far.....
***************

Group: Admin
Posts: 15,879
Joined: 11-September 03
From: Hurst, TX.
Member No.: 1,143
Region Association: NineFourteenerVille



I always looked at the voltmeter as a "mechanical turn signal indicator".

The damn thing is fairly worthless for actual voltage readings.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
davesprinkle
post Jul 10 2007, 12:49 AM
Post #13


Senior Member
***

Group: Members
Posts: 720
Joined: 13-October 04
From: Berkeley, CA
Member No.: 2,943
Region Association: None



Just for fun, I took my 914 voltmeter to work and verified its calibration with a laboratory power supply. Within its typical operating range (say, 10V to 14V), the meter's error was significantly less than 0.25V. Outside of that range, the error was less than 0.5V.

OK. You won't be making any precision measurements with this kind of accuracy, but it's good enough for use on the dash of a 914.

So if the meter is so decent on the bench, why is it so darned awful when hooked into the 914 wiring? The answer is this: the problem isn't with the meter -- it's with the wiring. The meter is accurately reporting the voltage at the FUSEBOX, not at the BATTERY. So if the voltmeter twitches by 0.5V in synch with the turnsignals, it's because the voltage at the fusebox is twitching by 0.5V.

So why does this happen? OK, just some rough numbers: 2 21W turnsignals will pull roughly 3.4 Amps. Given this current, a 0.5V twitch requires a wire resistance of only 0.15 Ohm. The circuits probably had that kind of resistance when they were fresh out of the factory -- 30 years of oxidation on the terminals has only made the resistance greater.

The fundamental problem is one of design -- the engineers neglected to ensure that the voltage sense lead carries little current.

So what's the solution? Run a new voltage sense lead all the way from the battery positive terminal. Connect it to the voltmeter by passing it through the contacts of a relay. Switch the coil of the relay with the previous voltmeter lead. There you go. The resistance of our new sense lead isn't significantly less, but because none of our lighting currents flow across that resistance, we'll no longer have the voltage error. The key here is to use the sense lead ONLY for sensing -- if you have any other load being fed by the lead, you'll corrupt the accuracy of the meter.

Or you could just tolerate the twitching needle...
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Bartlett 914
post Jul 10 2007, 10:02 AM
Post #14


Advanced Member
****

Group: Members
Posts: 2,216
Joined: 30-August 05
From: South Elgin IL
Member No.: 4,707
Region Association: Upper MidWest



QUOTE(davesprinkle @ Jul 9 2007, 10:49 PM) *

Just for fun, I took my 914 voltmeter to work and verified its calibration with a laboratory power supply. Within its typical operating range (say, 10V to 14V), the meter's error was significantly less than 0.25V. Outside of that range, the error was less than 0.5V.

OK. You won't be making any precision measurements with this kind of accuracy, but it's good enough for use on the dash of a 914.

So if the meter is so decent on the bench, why is it so darned awful when hooked into the 914 wiring? The answer is this: the problem isn't with the meter -- it's with the wiring. The meter is accurately reporting the voltage at the FUSEBOX, not at the BATTERY. So if the voltmeter twitches by 0.5V in synch with the turnsignals, it's because the voltage at the fusebox is twitching by 0.5V.

So why does this happen? OK, just some rough numbers: 2 21W turnsignals will pull roughly 3.4 Amps. Given this current, a 0.5V twitch requires a wire resistance of only 0.15 Ohm. The circuits probably had that kind of resistance when they were fresh out of the factory -- 30 years of oxidation on the terminals has only made the resistance greater.

The fundamental problem is one of design -- the engineers neglected to ensure that the voltage sense lead carries little current.

So what's the solution? Run a new voltage sense lead all the way from the battery positive terminal. Connect it to the voltmeter by passing it through the contacts of a relay. Switch the coil of the relay with the previous voltmeter lead. There you go. The resistance of our new sense lead isn't significantly less, but because none of our lighting currents flow across that resistance, we'll no longer have the voltage error. The key here is to use the sense lead ONLY for sensing -- if you have any other load being fed by the lead, you'll corrupt the accuracy of the meter.

Or you could just tolerate the twitching needle...


(IMG:style_emoticons/default/agree.gif)
Good writeup Dave. You are spot on here. I like the idea of using the old volt meter connection to energize a small relay. This also will save on draining the battery over long periods (although that is a very small drain).
User is offlineProfile CardPM
Go to the top of the page
+Quote Post

Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 



- Lo-Fi Version Time is now: 31st October 2024 - 05:35 PM