 Exhaust leaks, Any tricks to getting the HEs to seat properly? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| KaptKaos |
 Apr 9 2008, 12:02 AM
Post
#1
|
|
Family  Group: Members Posts: 4,009 Joined: 23-April 03 From: Near Wausau Member No.: 607 Region Association: Upper MidWest  |
I have had my heat exchangers off and on now about 4 times, trying to make sure that they are seated and tight. I have checked the copper gasket, put in new ones and still I get popping or back firing on decel.
Tonight I pulled the driver's side and flat filed the tops of the HEs to make sure I have a good surface. Nothing drastic, just trying to make it flat and smooth. Is there any trick to getting everything buttoned up properly? |
   |
 
|
  |
Replies
| jsayre914 |
Apr 9 2008, 01:05 PM
Post
#2
|
|
Speed Up !!! Group: Members Posts: 3,188 Joined: 10-February 08 From: Timonium MD 21093 Member No.: 8,696 Region Association: MidAtlantic Region |
I just installed my stailless HEs on my car last night with a new bursch exaust. got the kit from AA. I did not heat my rings first, I cannot run the car yet, I havent finished putting it back togeather on the top side. Is it going to leak gaurenteed?? cause I spent a good while getting it perfect straight and tight. (IMG:style_emoticons/default/212.gif)
|
|
|
|
Posts in this topic
KaptKaos Exhaust leaks Apr 9 2008, 12:02 AM
sww914 Anneal the copper seals before you bolt up the exh... Apr 9 2008, 12:56 AM
KaptKaos
Anneal the copper seals before you bolt up the ex... Apr 9 2008, 01:07 AM Challe Take them out, heat them as sww914 says, let them ... Apr 9 2008, 01:46 AM porsche914gt Check your intakes at the head. A leak there can m... Apr 9 2008, 03:52 AM Gint :agree: Popping out the exhaust does not necessari... Apr 9 2008, 07:06 AM Garland I used two copper gaskets, instead of one. took ca... Apr 9 2008, 11:37 AM Cap'n Krusty
I used two copper gaskets, instead of one. took c... Apr 9 2008, 12:06 PM Gint BTW, torching an asbestos filled copper crush wash... Apr 9 2008, 04:00 PM Mike914 And exactly 'who in the world' suggested t... Apr 9 2008, 11:46 PM rjames Do as the Cap'n says. Use one and only one cop... Apr 9 2008, 12:35 PM KaptKaos
Also, Gint makes a good point. How do you know th... Apr 9 2008, 12:50 PM Rand Don't worry about it jsayre914. Annealing is n... Apr 9 2008, 01:32 PM Gint And exactly 'who in the world' suggested t... Apr 10 2008, 08:55 AM purple Can't you just get the copper rings from jake ... Apr 10 2008, 11:57 AM Rand I'm not speaking for Jake, but I'll bet a ... Apr 10 2008, 01:17 PM Gint
I'm not speaking for Jake, but I'll bet a... Apr 10 2008, 05:02 PM Rand
I'd have to re-read this whole thread, but I ... Apr 10 2008, 05:12 PM Challe Cap'n is absolutly right, torching an asbestos... Apr 10 2008, 02:58 PM SLITS Must be that time of the month again. Apr 10 2008, 05:14 PM KaptKaos I need to redo it because I have a leak somewhere.... Apr 10 2008, 06:57 PM tod914 "I've applied some Loctite 518 to both si... Apr 10 2008, 07:07 PM purple
"I've applied some Loctite 518 to both s... Apr 11 2008, 03:56 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 16th June 2024 - 06:21 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.