 Door gaps are not even any more!, Now what??? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| FourBlades |
 Apr 4 2009, 01:31 PM
Post
#1
|
|
From Wreck to Rockin  Group: Members Posts: 2,056 Joined: 3-December 07 From: Brevard, FL Member No.: 8,414 Region Association: South East States 
 |
I was test fitting my doors before painting them and noticed this:
Driver side.  Passenger side. Attached image(s) 
|
   |
 
|
  |
Replies
| FourBlades |
Apr 6 2009, 11:52 AM
Post
#2
|
|
From Wreck to Rockin Group: Members Posts: 2,056 Joined: 3-December 07 From: Brevard, FL Member No.: 8,414 Region Association: South East States
|
Mark: I did a fair amount of seam welding on mine. Maybe 25% of the tops and less of the bottoms. I also did the seam welding in a short time. Part of the problem is that I had finally learned to make a really pretty seam weld so I think I just went overboard. The top still fits pretty well. It takes a little effort to lock the front latches. I am going to check it again to see if the windshield frame is bending. Man worrying about that is going to keep me from sleeping at all at work today... How do you use a porta power to stretch a car body? Pete: I am sure that is the thread I was reading. How did your guy know where to jack up your car? I wonder if your car naturally stretches when on jack stands because of the weight overhanging the front and rear jack stand points? Maybe you need that stretch to counter act the shrinkage? It would be nice to get this down to a repeatable science, for the sake of future 914s... John |
|
|
|
| horizontally-opposed |
Apr 6 2009, 12:33 PM
Post
#3
|
|
Advanced Member Group: Members Posts: 3,456 Joined: 12-May 04 From: San Francisco Member No.: 2,058 Region Association: None
|
QUOTE(FourBlades @ Apr 6 2009, 10:52 AM)  How did your guy know where to jack up your car? I wonder if your car naturally stretches when on jack stands because of the weight overhanging the front and rear jack stand points? Maybe you need that stretch to counter act the shrinkage? Experimentation + years and years of working with metal. He welded it cold and was super mindful of the potential for problems others had experienced -- and still got shrinkage. Fortunately, he knew what he was doing and was able to fix the problem. Both doors fit up nicely and close perfectly. The final test will be the windows... pete |
|
|
|
| Wes V |
Apr 6 2009, 03:03 PM
Post
#4
|
|
Member Group: Members Posts: 482 Joined: 11-October 07 From: Los angeles Member No.: 8,211 |
QUOTE(horizontally-opposed @ Apr 6 2009, 11:33 AM) Fortunately, he knew what he was doing and was able to fix the problem. pete By doing what? Wes |
|
|
|
Posts in this topic
FourBlades Door gaps are not even any more! Apr 4 2009, 01:31 PM
FourBlades The gaps were ok before I welded in my Engman kit.... Apr 4 2009, 01:35 PM
ConeDodger
The gaps were ok before I welded in my Engman kit... Apr 4 2009, 01:48 PM
SirAndy
I have also heard of putting bracing in the door ... Apr 4 2009, 02:02 PM SirAndy
Now WTF do I do???
Put the car on a lift, open t... Apr 4 2009, 02:05 PM FourBlades > Put the car on a lift, open the doors and use... Apr 4 2009, 02:12 PM FourBlades I did use a brace bolted to the upper seat belt mo... Apr 4 2009, 02:09 PM SirAndy
Any measurements I could do using simple tools to... Apr 4 2009, 02:36 PM Richard Casto
I did use a brace bolted to the upper seat belt m... Apr 6 2009, 09:19 AM JazonJJordan
I did use a brace bolted to the upper seat belt m... Jul 29 2009, 11:03 AM Bartlett 914 I feel your pain. I repaired my 75 when I got it i... Apr 4 2009, 03:11 PM FourBlades Thanks man...did you have any trouble getting your... Apr 4 2009, 03:26 PM sww914 It will be very difficult or impossible to find an... Apr 4 2009, 03:48 PM FourBlades According to wikipedia, steel expands .00000645 in... Apr 4 2009, 04:03 PM Wes V I've got a question for the author of this str... Apr 4 2009, 05:45 PM FourBlades Wes,
This is a really good question. I went out ... Apr 4 2009, 06:14 PM drive-ability I had that happen as well when I installed some st... Apr 4 2009, 06:43 PM r_towle The A pillar, at least the part that the door hing... Apr 4 2009, 07:29 PM FourBlades Rich,
Thanks for the suggestion. Have you tried ... Apr 4 2009, 07:40 PM r_towle Yes I have done it.
Push on the outer rear b-pilla... Apr 4 2009, 07:53 PM FourBlades OK, cool, I will try it tomorrow.
Thanks....John Apr 4 2009, 08:23 PM Bartlett 914 :popcorn: Apr 5 2009, 11:08 AM charliew I would think the passenger side will be easier to... Apr 5 2009, 11:28 AM FourBlades Charlie,
Thanks for the suggestions. I was hopi... Apr 5 2009, 11:52 AM horizontally-opposed
I am pretty sure I read on some forum that a guy ... Apr 6 2009, 10:10 AM Richard Casto
I am pretty sure I read on some forum that a guy... Apr 7 2009, 06:54 AM charliew About thirty years ago I torch welded the floors i... Apr 5 2009, 12:13 PM Wes V I'm trying to get my mind around this whole ... Apr 6 2009, 09:08 AM McMark
In my experience, this is the problem, John. I r... Apr 6 2009, 09:56 AM andys When I welded my Engman kit, I measured my door ga... Apr 6 2009, 10:39 AM 6freak
I was test fitting my doors before painting them ... Apr 6 2009, 10:42 AM Wes V I think something to think about would be to do on... Apr 6 2009, 03:01 PM horizontally-opposed
Fortunately, he knew what he was doing and was a... Apr 6 2009, 03:39 PM FourBlades Mr. C: I was wondering about that too. If I neede... Apr 6 2009, 11:56 AM 6freak
Mr. C: I was wondering about that too. If I need... Apr 6 2009, 12:30 PM FourBlades Slim line hinges may work....hmm..
Great, windows... Apr 6 2009, 02:56 PM burton73 John,
Your post was freaking me out all weekend. ... Apr 6 2009, 03:20 PM FourBlades Bob: Your door gap looks pretty good. Sounds lik... Apr 6 2009, 05:58 PM r_towle So,
To use a hydraulic unit to spread the door, y... Apr 6 2009, 06:33 PM FourBlades Rich,
Which part of the rear door jamb do you res... Apr 6 2009, 06:52 PM r_towle outer edge so you are pushing against the fender (... Apr 6 2009, 07:14 PM charliew Adding the material will fix the small door but I... Apr 6 2009, 07:18 PM Wes V It sure would be nice if somebody stepped up with ... Apr 6 2009, 07:56 PM FourBlades Richard,
I think I made the same mistake when I p... Apr 7 2009, 07:44 AM Richard Casto John,
I think part of the problem is that if I kn... Apr 7 2009, 08:13 AM charliew Welding never spreads any structure. It will alway... Apr 7 2009, 10:08 AM Richard Casto
Welding never spreads any structure. It will alwa... Apr 7 2009, 12:55 PM charliew The fact that the engman kit covers the top and in... Apr 7 2009, 01:12 PM Bartlett 914
Heating the driver side bottom might help close j... Apr 7 2009, 01:30 PM charliew
Heating the driver side bottom might help close ... Apr 8 2009, 12:18 AM McMark John, I've used a PortaPower between the front... Apr 7 2009, 05:48 PM atomix8 I realize I'm thread hijacking, AND pulling ou... Jul 27 2009, 07:54 PM tracks914 Yours looks easy to fix.
Your door is too low at ... Jul 28 2009, 08:46 PM atomix8
Yours looks easy to fix.
Your door is too low at... Jul 29 2009, 05:42 PM r_towle
Yours looks easy to fix.
Your door is too low a... Jul 29 2009, 07:12 PM rick 918-S
[quote name='atomix8' post='1196947' date='Jul 29... Jul 29 2009, 08:16 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 1st August 2025 - 06:34 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.