 Review of Tangerine's stainless fuel lines. |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Jakeodoule |
 Oct 1 2009, 11:53 AM
Post
#1
|
|
Member  Group: Members Posts: 353 Joined: 10-October 08 From: Des Moines Iowa Member No.: 9,630 Region Association: Pacific Northwest  |
If this is in the wrong place, sorry.
I installed they're fuel lines last night and I must say it is a great product. It beats the hell out of trying to get the right bend on some brake lines. Plus they are stainless. They went right in according to directions and the bends are perfect. I had my motor out already but I could see doing it with the engine in place no problem. They are a bit $pendy, but if you were bending them yourself from brake tubing I could see spending a ton of time to get them right. Also whats your car worth after all the time and money you put into it. a 150 bucks is not alot of money if its burning on the side of the road.... I think the engine compartment lines could be a bit longer to reach down around the corner of the hell hole but overall I give them an A+ Thanks and I will now drive without worrying about the plastic fuel lines. |
   |
 
|
  |
Replies
| JeffBowlsby |
Oct 1 2009, 02:32 PM
Post
#2
|
|
914 Wiring Harnesses & Beekeeper Group: Members Posts: 8,907 Joined: 7-January 03 From: San Ramon CA Member No.: 104 Region Association: None 
|
Do these metal lines bang together especially in the center tunnel, when going over bumps in the road? If not...why not?
BTW The 1970-74 fuel lines were Nylon 6 which is milky white when new. Nylon embrittles with exposure to moisture over a long period of time. The 1975-76 cars have black-colored lines which seem to be much mroe durable, but I do not know what material they are. |
|
|
|
Posts in this topic
Jakeodoule Review of Tangerine's stainless fuel lines. Oct 1 2009, 11:53 AM
zymurgist Cool review! I spent a lot of time bending th... Oct 1 2009, 11:59 AM Jakeodoule just go to they're site for pics and pricing.
... Oct 1 2009, 12:24 PM
zymurgist
just go to they're site for pics and pricing.... Oct 1 2009, 12:55 PM Vysoc
If this is in the wrong place, sorry.
I installed... Oct 1 2009, 12:41 PM Jakeodoule I would think they wouldn't bang around. There... Oct 1 2009, 02:48 PM tat2dphreak
I put in aluminum racing lines from Summit, Jef... Oct 1 2009, 02:50 PM Vysoc Once the stainless steel lines are in place they a... Oct 1 2009, 03:12 PM Jeff Bowlsby That actually describes my question and concern pe... Oct 1 2009, 03:41 PM neil30076
Also if they 'lay perfectly against the righ... Oct 1 2009, 03:56 PM Racer Chris
At some point (OK, OK, it may be a long time, bt... Oct 1 2009, 05:47 PM bperry
At some point (OK, OK, it may be a long time, b... Oct 2 2009, 07:46 PM iamchappy No need to review as they are fabulous..... Oct 1 2009, 05:34 PM Cevan Mine have been in for 7000 miles of New England dr... Oct 1 2009, 06:02 PM bandjoey With the tough new rubbers, why not just run rubbe... Oct 1 2009, 07:27 PM oh no, not again! Thanks for the review Jake! Now I know my effo... Oct 2 2009, 10:50 AM 2-OH! Jeff:
I used the SS lines as well, but I sliced a... Oct 2 2009, 05:47 PM ClayPerrine I have done the lines in my car from scratch, usin... Oct 2 2009, 09:45 PM Gigamight Thanks for the thumbs up on this product. I have b... Oct 3 2009, 11:38 AM Jakeodoule
Thanks for the thumbs up on this product. I have ... Oct 3 2009, 01:00 PM rhodyguy jeff, if you put the little black pieces of plasti... Oct 3 2009, 01:20 PM Sparky I've had the opportunity to see a lot of the p... Oct 3 2009, 11:06 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 11th May 2025 - 08:28 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.