 Master cylinder, Installation issues |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| jsaum |
 Dec 28 2009, 01:14 AM
Post
#1
|
|
Senior Member  Group: Members Posts: 530 Joined: 12-June 07 From: Everett, WA Member No.: 7,809 Region Association: None  |
Anyone have advice on the best way to get the reservoir tubes and grommets into to the master cylinder? I couldn't get them to slip in with the grommets in the master cylinder so I tried pushing them on the metal tubes and then pressing them in neither way is working. I have every thing else in place.
|
   |
 
|
  |
Replies
| Cap'n Krusty |
Dec 29 2009, 09:50 AM
Post
#2
|
|
Cap'n Krusty Group: Members Posts: 10,794 Joined: 24-June 04 From: Santa Maria, CA Member No.: 2,246 Region Association: Central California |
"Pull the lines from the reservoir"? THAT sounds like the hardest way of all. Install the grommets and the washers, lube them with brake fluid, install the m/c, and pull the tubes in with a pair of needle nose vise grips and a sturdy hook tool. Sure it's hard, but so is life. Suck it up, folks. The Cap'n
|
|
|
|
| jsaum |
Dec 29 2009, 01:06 PM
Post
#3
|
|
Senior Member Group: Members Posts: 530 Joined: 12-June 07 From: Everett, WA Member No.: 7,809 Region Association: None |
QUOTE(Cap'n Krusty @ Dec 29 2009, 07:50 AM)  "Pull the lines from the reservoir"? THAT sounds like the hardest way of all. Install the grommets and the washers, lube them with brake fluid, install the m/c, and pull the tubes in with a pair of needle nose vise grips and a sturdy hook tool. Sure it's hard, but so is life. Suck it up, folks. The Cap'n I bit the bullet and took the harder route pulling the gas tank! The master cylinder is in brake system is completly rebuilt and on to the next project the fuel system! Oh what fun! |
|
|
|
Posts in this topic
jsaum Master cylinder Dec 28 2009, 01:14 AM
ArtechnikA
Anyone have advice on the best way to get the res... Dec 28 2009, 05:09 AM GeorgeRud Rich's way is by far the best way, but if you ... Dec 28 2009, 06:50 AM DBCooper There are aftermarket M/C's that I swear won... Dec 28 2009, 07:31 AM
jsaum
There are aftermarket M/C's that I swear won... Dec 28 2009, 10:39 AM SLITS The aftermarket one is the Euro Parts one. They d... Dec 28 2009, 12:04 PM SUNAB914 I used two lockjaw pliers to pull down on the line... Dec 29 2009, 08:55 AM RiqueMar I'll be noting this topic in a few days. I was... Dec 30 2009, 12:41 AM greenie
"Pull the lines from the reservoir"? ... Dec 30 2009, 07:54 PM ppeters914 This thread started about reinstalling the reservo... Dec 31 2009, 11:21 AM ppeters914 Ack! Never mind. Found Pelican Parts tech arti... Dec 31 2009, 11:33 AM ArtechnikA
I get that you need to get slack in the reservoir... Dec 31 2009, 01:00 PM jsaum
[quote name='jsaum' post='1256169' date='Dec 29 2... Dec 31 2009, 12:51 PM rfuerst911sc Here's how I did it. Loosen the clamp that hol... Dec 30 2009, 04:32 AM etcmss I did it your first way and struggled and was succ... Dec 30 2009, 06:16 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 3rd June 2024 - 02:08 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.