 Is my case shot? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Cevan |
 Jan 4 2010, 07:47 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,079 Joined: 11-December 06 From: Western Massachusetts Member No.: 7,351  |
So after I had removed all the head studs from the case, I noticed a couple had come out real hard, as if something was wrong with the threads. After cleaning the threads of the stud, I couldn't thread them back in the two suspect holes.
I got a 12mmx 1.5tap and chased those holes. Now, the head studs go right in and they wiggle!! Even after I bottom them out, they can be moved relative to where they exit the case. Is the case shot? What did I do wrong? |
   |
 
|
  |
Replies
| VaccaRabite |
Jan 6 2010, 02:12 PM
Post
#2
|
|
En Garde! Group: Admin Posts: 13,754 Joined: 15-December 03 From: Dallastown, PA Member No.: 1,435 Region Association: MidAtlantic Region 
|
Before you go and spend $100 on the TimeCert kit... Consider this.
I had a local machinist install a time cert for $25. Now, granted, if you have to install 6 or 7 of them, its cheaper to do it yourself. But if you only need one done, its cheaper to have it done for you. Zach |
|
|
|
Posts in this topic
Cevan Is my case shot? Jan 4 2010, 07:47 PM
bam914 They should thread in tight like that. The only t... Jan 4 2010, 08:07 PM
Van
They should thread in tight like that. The only ... Jan 5 2010, 08:06 AM Cevan
They should thread in tight like that. The only... Jan 5 2010, 09:12 AM Cap'n Krusty A standard tap, the one everybody has, is NOT mean... Jan 4 2010, 08:51 PM Cevan Seeing as I screwed up only one of the case halves... Jan 4 2010, 09:42 PM bdstone914
Seeing as I screwed up only one of the case halve... Jan 4 2010, 10:05 PM kwales While you were cleaning the studs, did you notice ... Jan 4 2010, 10:36 PM Mark Henry And NO to using two different case halves. They ar... Jan 4 2010, 10:41 PM sww914 Take it to a machine shop and have them fix it. It... Jan 4 2010, 10:58 PM Cevan Thanks for the replies. Looking back on what I di... Jan 5 2010, 07:10 AM Rand My bad - I was thinking exhaust studs. Disregard
... Jan 5 2010, 09:45 AM Jake Raby You should have used a thread chaser, not a tap. T... Jan 5 2010, 09:55 AM Cevan
You should have used a thread chaser, not a tap. ... Jan 5 2010, 01:50 PM brp986s Definitely have a shop do it, and a good one at th... Jan 5 2010, 03:40 PM r_towle
You should have used a thread chaser, not a tap.... Jan 5 2010, 04:52 PM underthetire :agree:
Just make sure your table is square to th... Jan 5 2010, 04:54 PM kwales Most drill presses aren't an option....
That ... Jan 5 2010, 06:27 PM r_towle A drill press with a large top bolted in place wil... Jan 5 2010, 08:05 PM Dr Evil Thanks for posting this mistake. I have done simil... Jan 5 2010, 08:14 PM jmill
While you might be tempted to spend all your mone... Jan 5 2010, 09:30 PM Cevan Is a thread locker required when reinstalling the ... Jan 6 2010, 09:15 AM underthetire http://www.mcmaster.com/#inch/metric-threa...inser... Jan 6 2010, 11:24 AM Cevan
Before you go and spend $100 on the TimeCert... Jan 6 2010, 02:30 PM underthetire
Before you go and spend $100 on the TimeCer... Jan 6 2010, 02:43 PM Cevan I'm getting a headache. :D
I think I'll ... Jan 6 2010, 02:47 PM ME733 :popcorn: Just out of curosity, why did you remov... Jan 6 2010, 06:39 PM r_towle Brockton, Dedham and Newburyport.
There are other... Jan 6 2010, 08:52 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 4th July 2025 - 03:25 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.