 Can someone perform this experiment?, How does soda blasting work on headlight bezels? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| smontanaro |
 Jan 19 2010, 11:12 AM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,190 Joined: 3-June 05 From: Evanston, IL Member No.: 4,197 Region Association: Upper MidWest  |
Can someone with a soda blaster and some trashed headlight bezel(s) see if soda will take off stains and paint without damaging the plastic? I'm curious. I have neither a soda blaster nor a sacrificial headlight bezel. I do, however, have a car with headlight bezels which were painted black at one point in its lifetime. I'd like to know if there is any hope for them being restored to their original whiteness or if I should start looking for a new set.
Thanks, Skip |
   |
 
|
  |
Replies
| Gint |
Jan 20 2010, 05:28 PM
Post
#2
|
|
Mike Ginter Group: Admin Posts: 16,106 Joined: 26-December 02 From: Denver CO. Member No.: 20 Region Association: Rocky Mountains  |
Found some white headlight surrounds. And they're badly discolored. Should make for a good test.
Give me 30 minutes or so. It's not exactly warm out there though...  |
|
|
|
Posts in this topic
smontanaro Can someone perform this experiment? Jan 19 2010, 11:12 AM
underthetire You can make your own soda blaster with some tubin... Jan 19 2010, 11:47 AM ConeDodger I have a set hanging in my garage that were simila... Jan 19 2010, 12:04 PM Vacca Rabite I think the OP is talking about the plastic surrou... Jan 19 2010, 12:52 PM
ConeDodger
I think the OP is talking about the plastic surro... Jan 19 2010, 01:00 PM kwales Wow!!!!!!
That was a bug ... Jan 19 2010, 12:58 PM Mark Henry Is there anywhere that sells soda in bulk?
Has any... Jan 19 2010, 01:16 PM Vacca Rabite
Is there anywhere that sells soda in bulk?
My bl... Jan 19 2010, 01:23 PM McMark Soda Blasting Media Jan 19 2010, 01:21 PM underthetire gRDX6BPzpj0
Shows using it on a glass vette.
Sor... Jan 19 2010, 01:52 PM Rav914 I used a very homemade soda blaster on a windshiel... Jan 19 2010, 03:21 PM Gint Didn't see this until now. I still have some ... Jan 19 2010, 10:54 PM snakemain Bought a dedicated 10lb soda blaster at Harbor Fre... Jan 20 2010, 08:44 AM Eric_Shea Industrial soda works but it can leave them a tad ... Jan 20 2010, 10:34 AM 914Sixer Harbor Freight has blasting soda if you have one c... Jan 20 2010, 12:57 PM kwales I think you need a dry ice blaster.
Those suckers... Jan 20 2010, 01:04 PM Gint This actually took 5 minutes or so. Plain old Cos... Jan 20 2010, 05:55 PM Sleepin
This actually took 5 minutes or so. Plain old Co... Jan 22 2010, 09:50 AM Gint Better pic?
Jan 20 2010, 06:00 PM kwales Usually when you abrade flexible plastic, it gets ... Jan 21 2010, 12:13 PM Gint Usually when you abrade flexible plastic, it gets ... Jan 22 2010, 08:47 AM smontanaro Gint - Thanks for the test. That gives me the not... Jan 21 2010, 09:49 PM Vacca Rabite If you have an air compressor, you really can just... Jan 22 2010, 08:14 AM smontanaro if you don't have a compressor, this is *just*... Jan 22 2010, 10:12 AM Vacca Rabite
if you don't have a compressor, this is *just... Jan 22 2010, 11:53 AM zymurgist
the smallest I would get is a 24 gallon oil coole... Jan 22 2010, 12:10 PM Vacca Rabite I think that soda is supposed to be a single use m... Jan 22 2010, 08:59 AM Gint One time use of soda what I've been lead to be... Jan 22 2010, 09:05 AM underthetire The Fuzzy should be able to be knocked off with pl... Jan 22 2010, 09:59 AM underthetire Air is the only way to go !
I picked this up
h... Jan 22 2010, 12:21 PM smontanaro *sigh* let me try again... http://www.dewalt.com/u... Jan 22 2010, 04:57 PM Gint *sigh* let me try again... [url=http://www.dewalt.... Jan 22 2010, 05:16 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 2nd April 2026 - 04:41 PM |
Invision Power Board
v9.1.4 © 2026 IPS, Inc.