 Front Brakes Dragging, wheels don't spin free |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| 7TPorsh |
 Jan 25 2010, 03:28 PM
Post
#1
|
|
7T Porsh  Group: Members Posts: 2,691 Joined: 27-March 06 From: Glendale Ca Member No.: 5,782 Region Association: Southern California 
 |
Tried looking in search...
I changed out the following; - Front brake rotors - Front bearings and seals - Front pads I tried to push back the piston enough to get the pads in...ending up tapping them in but not too much effort. I noticed that it was tight. Thinking it will loosen up, i finished the job. I get the car on the ground and out on the road a little and realize that the car just doesn't roll...i am working against the brakes. Brakes didn't 'adjust" and are still really tight. Lock nut is not overly tightened. |
   |
 
|
  |
Replies
| underthetire |
Jan 26 2010, 06:02 PM
Post
#2
|
|
914 Guru Group: Members Posts: 5,062 Joined: 7-October 08 From: Brentwood Member No.: 9,623 Region Association: Northern California |
Ok, just gotta ask here. New pads (thicker than old ones) new rotors (thicker than old ones), so...
If there is varnish at the back of the piston bore on the calipers, and he had to force them back, would it not make sense that the piston could now be frozen in the caliper bore? I would think if you were doing pads,rotors,and bearings, it would be well worth the 12 bucks or so per kit to re build the calipers, and put new lines on. (from Eric) DON'T BUY THE EBAY KITS. they don't have everything you need. |
|
|
|
Posts in this topic
7TPorsh Front Brakes Dragging Jan 25 2010, 03:28 PM
kg6dxn Technically disc brakes should drag a little. with... Jan 25 2010, 03:34 PM 914Sixer Jack up each wheel and spin them. Find out which ... Jan 25 2010, 03:34 PM 7TPorsh off the ground they don't spin. I have to grab... Jan 25 2010, 03:44 PM
kg6dxn
off the ground they don't spin. I have to gra... Jan 25 2010, 03:51 PM
etcmss did the bearings go on easily and is the rotor ful... Jan 25 2010, 03:52 PM dr914@autoatlanta.com and make sure that the pedal itself is not stickin... Jan 25 2010, 03:51 PM bandjoey Are the clearance clips in place on the pistons? ... Jan 25 2010, 03:56 PM Eric_Shea
:huh: (those are piston positioning clips meant... Jan 25 2010, 04:26 PM etcmss Eric -are you saying the hose(s) actually get a bu... Jan 26 2010, 04:14 PM jmill
Eric -are you saying the hose(s) actually get a b... Jan 26 2010, 05:04 PM 7TPorsh I don't think it's the lines but will look... Jan 26 2010, 05:39 PM ahdoman another thought - If, when you took the calipers o... Jan 26 2010, 06:41 PM Cap'n Krusty '70-'71 and most '72s took the T4 roto... Jan 26 2010, 07:04 PM Eric_Shea
The caliper offset is quite different. I doubt ... Jan 26 2010, 11:51 PM sean_v8_914 frozen caliper pistons. dark brown nasty brake flu... Jan 27 2010, 08:47 AM ME733 ......AND when everything mentioned has been check... Jan 27 2010, 11:14 AM 7TPorsh
......AND when everything mentioned has been chec... Jan 27 2010, 05:22 PM etcmss Pelican-- http://www.pelicanparts.com/catalog/shop... Jan 27 2010, 06:08 PM topatrout914 Make sure you did not overtighten the spindle nut.... Jan 28 2010, 10:09 AM ME733 I purchased the "expanding Springs,"....... Jan 28 2010, 01:48 PM 7TPorsh i looked at Pelican, it looks like they only have ... Jan 28 2010, 02:19 PM 914rrr Resurrecting an older thread that eliminates some ... Oct 23 2026, 12:28 PM |
3 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
1 Members: T.Rick6
|
Lo-Fi Version | Time is now: 23rd October 2026 - 05:24 PM |
Invision Power Board
v9.1.4 © 2026 IPS, Inc.