 Tie Rod Ball Joint Question |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| kenshapiro2002 |
 May 11 2010, 12:09 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,444 Joined: 23-July 09 From: Bawlmer, MD Member No.: 10,598 Region Association: MidAtlantic Region  |
The bellows on my left side tie rod end ball joint is shot (obviously). I'm assuming the downside is loss of grease...ingestion of dirt, and premature wear? Anyway, what's the fix? Do I need to replace the whole joint or can the bellows be replaced. Hand tools? Ease of repair on a scale of 1-10 with 1 being changing a tire and 10 being rebuilding the trans.?
 |
   |
 
|
  |
Replies
| underthetire |
May 11 2010, 05:23 PM
Post
#2
|
|
914 Guru Group: Members Posts: 5,062 Joined: 7-October 08 From: Brentwood Member No.: 9,623 Region Association: Northern California |
PB blaster
Aero Kroil-better in my book or for the real DIY, acetone and ATF mixed 70 atf/30 acetone All super penetration oils, makes jobs like that a lot easier. Napa by my house carries Kroil, about 13 bucks a can. |
|
|
|
Posts in this topic
kenshapiro2002 Tie Rod Ball Joint Question May 11 2010, 12:09 PM
dr914@autoatlanta.com replace the end. They are cheap enough and chances... May 11 2010, 12:11 PM
kenshapiro2002 George,
Thanks. BTW, the inquiry is not an order.... May 11 2010, 12:13 PM
SirAndy
replace the end. They are cheap enough and chance... May 11 2010, 12:13 PM 6freak PB BLASTER IS YOUR FRIEND ..let soak for a day the... May 11 2010, 03:22 PM kenshapiro2002 PB Blaster (never heard of it) any better than CRC... May 11 2010, 04:09 PM r_towle Its actually a fairly easy project.
Jack it up and... May 11 2010, 05:18 PM kenshapiro2002 Thanks. Not really sure where you're telling m... May 11 2010, 05:26 PM kenshapiro2002 Rick,
There was no nut on the threaded rod of the... May 17 2010, 11:12 AM r_towle Simple way is to have sears replace the end for yo... May 11 2010, 05:33 PM kenshapiro2002 That's no fun at all, and doesn't increase... May 11 2010, 05:35 PM kenshapiro2002 Speaking of alignment...the car drifts to the righ... May 13 2010, 04:30 PM jaxdream Ken
The removal is fairly easy , look at it . The ... May 11 2010, 05:51 PM jaxdream RE: Tie Rod Ball Joint Question May 11 2010, 05:53 PM Cap'n Krusty If you beat on the threaded end, you'll likely... May 11 2010, 05:59 PM kenshapiro2002 Thanks guys...as always. May 11 2010, 06:04 PM tat2dphreak
easy. I did the shocks the ball joints, bearings,... May 13 2010, 06:08 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 1st August 2025 - 07:16 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.