 Carb syncing question |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Cevan |
 May 13 2010, 05:39 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,079 Joined: 11-December 06 From: Western Massachusetts Member No.: 7,351  |
I'm trying to sync the carbs (Weber IDFs) on my new engine. I warmed it up and then let it idle at about 800 rpms. I disconnected the linkage and used the synchometer. On one carb, both barrels were very close to each other (5 and almost 5), while the other carb read a 5 and a 3. Is this indicative of a bent shaft or some other problem, or can this be adjusted?
I do recall removing the throttle plates from one of the carbs while I was cleaning them. I was going to remove the shaft but decided against it and put the plates back on. Might I have changed the position of one or both of the throttle plates in relation to the bore? Would this cause the problem? Also, fuel seems to be almost weeping in the area of the brass bolt and washer (#5 and 6 in the picture) directly under where the feed line connects to the carb. I used a new washer and tightened the bolt real good. Any ideas?  |
   |
 
|
  |
Replies
| Cevan |
May 14 2010, 08:22 PM
Post
#2
|
|
Senior Member Group: Members Posts: 1,079 Joined: 11-December 06 From: Western Massachusetts Member No.: 7,351 |
I recall putting the plates back on the way they came off. I just barely tightened the screws and then opened and closed the plates a few times to make sure they were seated correctly, and then tightened the screws.
|
|
|
|
| ME733 |
May 15 2010, 05:52 PM
Post
#3
|
|
Senior Member Group: Members Posts: 842 Joined: 25-June 08 From: Atlanta Ga. Member No.: 9,209 Region Association: South East States |
QUOTE(Cevan @ May 14 2010, 10:22 PM)  I recall putting the plates back on the way they came off. I just barely tightened the screws and then opened and closed the plates a few times to make sure they were seated correctly, and then tightened the screws. .................OK, just wanted to know if you might have reinstalled the butterflys backwards....they HAVE , a specific orentation...... |
|
|
|
Posts in this topic
Cevan Carb syncing question May 13 2010, 05:39 PM
9146986 Chris, unfortunately there could be a few other fa... May 13 2010, 06:22 PM 70_914
I'm trying to sync the carbs (Weber IDFs) on ... May 13 2010, 07:43 PM
cgnj Hi,
Fully seat air bypass screws. Use bypass scre... May 13 2010, 08:00 PM
r_towle
Hi,
Fully seat air bypass screws. Use bypass scr... May 13 2010, 08:53 PM jt914-6
I'm trying to sync the carbs (Weber IDFs) on... May 14 2010, 06:39 AM Cevan Perry, I found your writeup. I will go through th... May 13 2010, 07:57 PM 9146986 Yes, there should be a gasket at the velocity stac... May 14 2010, 05:29 AM Vacca Rabite :agree:
#48 is air bypass. Loosens the lock nut a... May 14 2010, 06:57 AM jmill Sounds like a vaccum leak or a plugged idle jet. ... May 14 2010, 07:34 AM jmill :stooges: Double post. May 14 2010, 07:36 AM ME733 ......AFTER removing the throttle plates.."on... May 14 2010, 03:51 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 7th July 2025 - 08:28 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.