 Changed the clutch, one more question... |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| ripper911 |
  Aug 22 2010, 05:41 PM
Post
#1
|
|
corde pulsum tangite  Group: Members Posts: 2,920 Joined: 25-April 10 From: Powder Springs, GA Member No.: 11,654 Region Association: South East States  |
Well, we got everything changed and back together.
I crank the car up and it just grinds when trying to shift. (IMG:style_emoticons/default/headbang.gif) Heres what I know... we didn't remove the flywheel/crankshaft seal so the shims were not messed with I used the rebuilt flywheel (although it looked awefully clean) so I thought we might have to do the shims but didn't think we would be able to do it with what we had available.. I've adjusted the cable at the release fork as much as it can, the pedal feels very tight, and the end of the fork hits the transmision case. I've read about shimming the ball in the bell housing of the tranny, but how? is that what we should do next, or go in and get the shims behind the flywheel in spec? we shifted the transmission while trying to get it back on the engine, whould that have thrown something off? not sure what to do next? |
   |
 
|
  |
Replies
| ws91420 |
Aug 23 2010, 08:40 PM
Post
#2
|
|
Yes I have one a Lensley 914 Group: Members Posts: 2,063 Joined: 10-September 03 From: Ruther Glen,VA (halfway between sticks and civilization) Member No.: 1,137 Region Association: MidAtlantic Region |
Did you replace the clutch cable yet? I kept trying to adjust a worn out clutch and ended up streching and snapping a cable.
|
|
|
|
Posts in this topic
ripper911 Changed the clutch Aug 22 2010, 05:41 PM
messix i think it's to put a washer between the pivot... Aug 22 2010, 05:48 PM
ripper911
i think it's to put a washer between the pivo... Aug 22 2010, 06:11 PM
messix
i think it's to put a washer between the pivo... Aug 23 2010, 08:02 PM Spoke
I've adjusted the cable at the release fork a... Aug 22 2010, 07:25 PM ripper911
I've adjusted the cable at the release fork ... Aug 23 2010, 04:28 PM jimkelly engine off
put car in 5th
push clutch in
have s... Aug 22 2010, 09:02 PM ripper911 I went back today and pulled the tranny again.
Me... Aug 23 2010, 04:24 PM Ductech Best advice i can give is that you should measure ... Aug 23 2010, 04:33 PM ripper911
Best advice i can give is that you should measure... Aug 23 2010, 04:46 PM JRust Still sounds like the clutch fork to me. Did you g... Aug 23 2010, 05:11 PM ripper911 Ah, the washer goes BEHIND the ball, in the tranny... Aug 23 2010, 06:06 PM SLITS You bought the flywheel from AA. Did they bother ... Aug 23 2010, 05:08 PM SLITS Ok, you asked for suggestions .... read this ........ Aug 23 2010, 06:59 PM Cap'n Krusty Did you replace the plastic ball cup on the releas... Aug 23 2010, 06:59 PM ripper911
Did you replace the plastic ball cup on the relea... Aug 24 2010, 04:55 AM Cap'n Krusty
Did you replace the plastic ball cup on the rele... Aug 24 2010, 07:39 AM tradisrad Like others say you need to put a washer under the... Aug 23 2010, 07:04 PM jsaum I had a problem with the clutch not wanting to dis... Aug 23 2010, 09:07 PM yeahmag I think normally you shim under the bushing that p... Aug 23 2010, 10:42 PM SUNAB914 My input to this from what I read.
Flywheel not i... Aug 24 2010, 07:02 AM brant I only read through this once, so forgive me if I ... Aug 24 2010, 07:53 AM ripper911 Alright, so I'll have to set the end play.
I r... Aug 24 2010, 12:00 PM ripper911 I just found something interesting on another thre... Aug 24 2010, 12:07 PM Spoke The little plastic ball cup in the clutch fork sho... Aug 24 2010, 12:39 PM jsaum Yes the plastic cup would affect the travel and pr... Aug 24 2010, 12:40 PM Bartlett 914 Why would it be missing unless you took it out? Ma... Aug 24 2010, 01:11 PM ripper911 We are pretty sure there wasn't one there on t... Aug 24 2010, 04:26 PM ripper911 one last question hopefully, I would like to know ... Aug 25 2010, 08:29 AM SLITS Somewhere in this thread I thought I told you they... Aug 25 2010, 10:59 AM ripper911
Somewhere in this thread I thought I told you the... Aug 25 2010, 11:15 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 2nd April 2026 - 02:37 PM |
Invision Power Board
v9.1.4 © 2026 IPS, Inc.