 SBC 350 exhaust question, Stock/custom?? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| pete |
 Sep 8 2010, 10:47 AM
Post
#1
|
|
Member  Group: Members Posts: 158 Joined: 23-August 10 From: New Jersey Member No.: 12,092 Region Association: North East States  |
I have a Renegade SBC 350 with shorty headers I will soon be installing in my 914. Looking at several threads/pics of this conversion it looks like almost all pipes from the header to the muffler loop under the axles. Is there a stock part number for these curved pipe sections (steel) or are they all basically custom?
|
   |
 
|
  |
Replies
| andys |
Sep 8 2010, 01:30 PM
Post
#2
|
|
Advanced Member Group: Members Posts: 2,165 Joined: 21-May 03 From: Valencia, CA Member No.: 721 Region Association: None 
|
Though not an SBC, I used stainless mandrel bends and routed the exhaust over the axles. Not sure which muffler shops can weld stainless (perhaps these days they all can), but it's a pretty simple task for a decent shop.
There are quite a lot of V8 exhaust system pictures on this site if you search around. I seem to recall a dual inlet/dual outlet Camaro muffler that fits in the original location that looked real nice. Andys Attached thumbnail(s) 
|
|
|
|
| pete |
Sep 8 2010, 02:25 PM
Post
#3
|
|
Member Group: Members Posts: 158 Joined: 23-August 10 From: New Jersey Member No.: 12,092 Region Association: North East States |
QUOTE(andys @ Sep 8 2010, 03:30 PM)  Though not an SBC, I used stainless mandrel bends and routed the exhaust over the axles. Not sure which muffler shops can weld stainless (perhaps these days they all can), but it's a pretty simple task for a decent shop. There are quite a lot of V8 exhaust system pictures on this site if you search around. I seem to recall a dual inlet/dual outlet Camaro muffler that fits in the original location that looked real nice. Andys Andy, thanks for the pic. It looks like you have two of the same pieces welded together on each side. |
|
|
|
| Mike Bellis |
Sep 8 2010, 02:32 PM
Post
#4
|
|
Resident Electrician Group: Members Posts: 8,347 Joined: 22-June 09 From: Midlothian TX Member No.: 10,496 Region Association: None 
|
QUOTE(pete @ Sep 8 2010, 01:25 PM) QUOTE(andys @ Sep 8 2010, 03:30 PM) Though not an SBC, I used stainless mandrel bends and routed the exhaust over the axles. Not sure which muffler shops can weld stainless (perhaps these days they all can), but it's a pretty simple task for a decent shop. There are quite a lot of V8 exhaust system pictures on this site if you search around. I seem to recall a dual inlet/dual outlet Camaro muffler that fits in the original location that looked real nice. Andys Andy, thanks for the pic. It looks like you have two of the same pieces welded together on each side. That is exactly what the Renegade exhaust tube looks like. Without the weld in the middle. |
|
|
|
Posts in this topic
pete SBC 350 exhaust question Sep 8 2010, 10:47 AM
messix if you can fab it by your self you could order som... Sep 8 2010, 10:50 AM messix oh and you'll find most of the stuff for the v... Sep 8 2010, 10:56 AM Phoenix-MN I have "shorty" headers and ran the exha... Sep 8 2010, 11:38 AM charliew I would just buy mandrel bent elbows and some stra... Sep 8 2010, 12:04 PM
pete
I would just buy mandrel bent elbows and some str... Sep 8 2010, 01:01 PM messix
I would just buy mandrel bent elbows and some st... Sep 8 2010, 01:08 PM kg6dxn
I have a Renegade SBC 350 with shorty headers I w... Sep 8 2010, 12:10 PM Andyrew I have the shorty headers, You have to watch out f... Sep 8 2010, 12:27 PM pete
I have the shorty headers, You have to watch out ... Sep 8 2010, 01:04 PM type47fan
I seem to recall a dual inlet/dual outlet Camaro... Sep 8 2010, 11:52 PM pete
I seem to recall a dual inlet/dual outlet Camar... Sep 9 2010, 07:07 AM andys
[quote name='type47fan' post='1368159' date='Sep ... Sep 9 2010, 09:33 AM BRAVE_HELIOS
I seem to recall a dual inlet/dual outlet Camar... Mar 1 2011, 07:11 PM matthepcat The nice thing about the dual in dual out magnaflo... Mar 3 2011, 09:30 PM BRAVE_HELIOS That's the main reason why I want to go that r... Mar 4 2011, 04:05 PM sww914
Though not an SBC, I used stainless mandrel bends... Mar 4 2011, 04:27 PM BRAVE_HELIOS Hmmm, what won't fit? :idea:
Though not an... Mar 4 2011, 04:33 PM computers4kids One major dis-advandtage of not going over the axl... Sep 9 2010, 07:52 AM joefri187
I have a Renegade SBC 350 with shorty headers I w... Mar 4 2011, 05:44 PM jimkelly or you can ignore form completely : ) Mar 4 2011, 06:32 PM BRAVE_HELIOS Not at all... it's free form! :)
or you... Mar 4 2011, 07:36 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 6th November 2025 - 09:46 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.