 broken rear suspension mount |
|
|
|
Tuesday, 15 July 2025 |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| stugray |
 Nov 21 2010, 02:45 PM
Post
#1
|
|
Advanced Member  Group: Members Posts: 3,825 Joined: 17-September 09 From: Longmont, CO Member No.: 10,819 Region Association: None  |
So I dropped the motor and what do I see?:
(IMG:http://www.914world.com/bbs2/uploads_offsite/i366.photobucket.com-10819-1290372313.1.jpg) Can I just re-weld this, or do I need to remove the whole piece and put in a new one? I suppose I should do both sides while I am at it? Any suggestions? Stu |
   |
 
|
  |
Replies
| dr914@autoatlanta.com |
Nov 21 2010, 05:26 PM
Post
#2
|
|
914 Guru Group: Members Posts: 8,188 Joined: 3-January 07 From: atlanta georgia Member No.: 7,418 Region Association: None |
The broken suspension console was such a common problem that the old Perfect Panels began making them almost the day after the cars rolled off the assembly line. Most of it was because owners were unaware of the acid leaking battery and therefore did nothing about it until one day when the bottom of the tire was leaning out. We back then repaired many that insurance companies would actually cover the costs!!!!!! W\Years later we bought the company when the owner died so now make them and STILL sell many.. We also install them so if you need some advice, do not hesitate to call or e mail Sean in our service department.
QUOTE(stugray @ Nov 21 2010, 01:45 PM)  So I dropped the motor and what do I see?: (IMG:http://www.914world.com/bbs2/uploads_offsite/i366.photobucket.com-10819-1290372313.1.jpg) Can I just re-weld this, or do I need to remove the whole piece and put in a new one? I suppose I should do both sides while I am at it? Any suggestions? Stu |
|
|
|
Posts in this topic
stugray broken rear suspension mount Nov 21 2010, 02:45 PM
Travis Neff I wouldn't weld it back up, replace it. Troub... Nov 21 2010, 03:07 PM Andyrew New Piece, Do Both.. Nov 21 2010, 03:10 PM Eric_Shea Check CFR for a repair piece I believe. Search is... Nov 21 2010, 03:46 PM brant Stu,
its common on track cars
there is a 914 gur... Nov 21 2010, 03:59 PM stugray OK replace then.
I have a plasma cutter & MIG... Nov 21 2010, 04:56 PM brant That picture is a fab mount, but with the -4cylind... Nov 21 2010, 05:10 PM Eric_Shea Brant has a brace similar to this one:
http://www... Nov 21 2010, 05:14 PM pktzygt I'm in the middle of mine. It's time consu... Nov 21 2010, 07:04 PM stugray Ok, I'm game.
Credit card in hand....
I dont... Nov 21 2010, 07:08 PM
dr914@autoatlanta.com http://www.autoatlanta.com/detail.php?Part...ial_n... Nov 22 2010, 09:41 AM brant brace You need a spot weld removing drill bit
abou... Nov 21 2010, 07:19 PM stugray So if I get the "Rear Pickup Points Reinforci... Nov 21 2010, 08:58 PM brant
So if I get the "Rear Pickup Points Reinforc... Nov 21 2010, 11:38 PM mepstein I would think you should replace the console and n... Nov 21 2010, 09:10 PM SirAndy I would think you should replace the console and n... Nov 21 2010, 09:31 PM stugray Thanks for the link - $211 ea. - OUCH!.
... Nov 22 2010, 09:52 AM Racer Chris
Thanks for the link - $211 ea. - OUCH!.
... Nov 22 2010, 10:27 AM 914Eric
IMO its a very fair price for that piece.
:ag... Nov 20 2012, 11:24 AM Phoenix-MN Just a heads up on prevenative maintenance. There ... Nov 22 2010, 10:13 AM Eric_Shea Restoration design has the console for $199.0... Nov 22 2010, 10:30 AM Racer Chris
Restoration design has the console for $199.... Nov 22 2010, 10:37 AM SirAndy Restoration design has the console for $199.0... Nov 22 2010, 12:18 PM dr914@autoatlanta.com We have a used drivers side on e bay right now: h... Nov 22 2010, 12:34 PM sixnotfour The one on ebay is not worth the time to remove it... Nov 22 2010, 02:25 PM Racer Chris
The one on ebay is not worth the time to remove i... Nov 22 2010, 06:24 PM stugray sixnotfour,
I did a search for "slits",... Nov 22 2010, 04:44 PM SirAndy I did a search for "slits", but didnt fi... Nov 22 2010, 05:19 PM sixnotfour
It is a genuine offer.
The west coast aint... Nov 23 2010, 05:19 AM Racer Chris
It is a genuine offer.
Fair enough. My apologi... Nov 23 2010, 09:41 AM stugray Ok, thanks for all the replies and offers for a us... Nov 27 2010, 12:58 PM Steve
Ok, thanks for all the replies and offers for a u... Dec 29 2011, 11:26 AM Racer Chris They do not interfere with the valve covers. Nov 27 2010, 03:23 PM SGB Oh man, Chris's reinforcement kit look like Da... Dec 29 2011, 11:46 AM Elliot Cannon I installed Chris' reinforcement kit in antici... Dec 29 2011, 01:55 PM stugray I just finished the entire engine bay this last we... Dec 29 2011, 02:24 PM rdauenhauer Looks like Im a bit late to this party, but having... Nov 20 2012, 09:19 PM Van914 I have one of Chris's kits without the removab... Nov 21 2012, 05:57 AM edwin Does anyone look at post dates these days? Nov 21 2012, 06:14 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 15th July 2025 - 01:11 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.