 Cooling Flaps |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| cdadaa |
 Oct 24 2010, 10:37 AM
Post
#1
|
|
Newbie  Group: Members Posts: 6 Joined: 25-May 09 From: Spring Creek, Nevada Member No.: 10,402 Region Association: None  |
Hi,
Is this the correct positioning for the cooling flaps with a cold unexpanded bellows? Somehow I think the rod may have been bent or the flaps twisted by the previous owner. I want to hook up the thermostat so I can have a wintertime heater. Thanks...Dan Attached thumbnail(s)  
|
   |
 
|
  |
Replies
| cdadaa |
Oct 24 2010, 05:53 PM
Post
#2
|
|
Newbie Group: Members Posts: 6 Joined: 25-May 09 From: Spring Creek, Nevada Member No.: 10,402 Region Association: None |
Look again...I believe the CHT is on the passenger side. The photo was taken from the flywheel (engine rear, front of car) side. BTW, this is going in a 912E.
|
|
|
|
| jaxdream |
May 10 2011, 07:33 AM
Post
#3
|
|
Senior Member Group: Members Posts: 974 Joined: 8-July 08 From: North Central Tennessee Member No.: 9,270 Region Association: South East States |
QUOTE(cdadaa @ Oct 24 2010, 03:53 PM)  Look again...I believe the CHT is on the passenger side. The photo was taken from the flywheel (engine rear, front of car) side. BTW, this is going in a 912E. Ok for the position of the engine in the 912E- Yes ( passenger side ) , position for the CHT sender to operate with Fuel Injection- NO , the CHT needs to be over the Number 3 cylinder to capture the hotest cylinder -per Porsche / VW configuration. We ( the forum members ) are trying to help with some advise . Good Luck , and do hope you get it running well. Jack / Jaxdream |
|
|
|
Posts in this topic
cdadaa Cooling Flaps Oct 24 2010, 10:37 AM
Sleepin That is the hot position IIRC. Oct 24 2010, 11:07 AM StratPlayer Thermostat cable connects with the connector in th... Oct 24 2010, 11:11 AM cdadaa So the flaps are both "up" or closed lik... Oct 24 2010, 11:21 AM Cap'n Krusty The system in question has ABSOLUTELY NOTHING to d... Oct 24 2010, 11:53 AM cdadaa That wasn't my question Mr. Cap'n! Oct 24 2010, 12:04 PM
Cap'n Krusty
That wasn't my question Mr. Cap'n!
... Oct 24 2010, 03:37 PM Jake Raby In the HOT position the diverter over the oil cool... Oct 24 2010, 12:56 PM abayer1969 :popcorn: Oct 24 2010, 03:39 PM cdadaa Thanks Jake...that makes sense. I'm good to g... Oct 24 2010, 05:31 PM gasman Looks like you have the heads on the wrong sides..... Oct 24 2010, 05:41 PM SirAndy BTW, this is going in a 912E.
And we knew that bec... May 9 2011, 09:14 PM ziggy Were the cable running to the thermo to break, wou... May 9 2011, 08:25 PM McMark ONLY attach the wire with the flaps in this positi... May 10 2011, 12:00 AM 914Mike
ONLY attach the wire with the flaps in this posit... May 10 2011, 01:20 AM vsg914
Looks like you have the heads on the wrong sides.... May 10 2011, 08:18 AM sean_v8_914 Jake was being subtle. write it on a calendar and ... May 10 2011, 09:33 AM McMark
Jake was being subtle. write it on a calendar and... May 10 2011, 10:43 AM 914Mike
Jake was being subtle. write it on a calendar an... May 10 2011, 11:34 AM McMark
True, but it would be 'when the bellows are _... May 10 2011, 06:04 PM enderw88
True, but it would be 'when the bellows [i]a... May 10 2011, 07:19 PM McMark I don't like it. I decree my interpretation t... May 10 2011, 07:30 PM enderw88
I don't like it. I decree my interpretation ... May 10 2011, 08:04 PM sean_v8_914 gramar police should has at least 200 posts to qua... May 11 2011, 08:01 AM 914Mike
Grammar police should have at least 200 posts to ... May 13 2011, 01:28 AM jaxdream phuch em , make hims dos a tyme aught &&... May 11 2011, 08:05 AM MikeM Just to be clear....I'm missing some parts fro... May 12 2011, 07:38 AM vsg914 Mike, the default is to the hot in case the cable ... May 12 2011, 09:33 AM SirAndy
Mike, the default is to the hot in case the cable... May 12 2011, 10:55 AM Root_Werks I see three major points that have been made to th... May 12 2011, 12:17 PM MikeM Thanks guys...if I would have thought about that f... May 12 2011, 07:51 PM avidfanjpl Mike,
On the standard temp gauge in the console i... May 12 2011, 09:24 PM 914Mike
...
On a cold motor, flap bolt tiedown should be... May 13 2011, 01:11 AM avidfanjpl Everyone has an opinion based on experience on the... May 13 2011, 01:29 AM |
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 29th December 2025 - 04:44 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.