 Weber problem |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| stock93 |
 Apr 5 2004, 08:17 PM
Post
#1
|
|
Member  Group: Members Posts: 333 Joined: 12-May 03 From: Huntsville, AL Member No.: 684 Region Association: South East States  |
I have a 2.0 type IV engine with 44idfs on it. I was going to sync the carbs today and noticed that even when not pumping the throttle the accelerator pump drips a stream of gas down into the throat of the carb enough that its pooling up a bit on the throttle plate. I'm getting popping back through the carbs. Timing is spot on and the valves are correctly adjusted. I take it this is a problem and they arent supposted to do this? It also smells like its still running to rich. I have 135 mains, 200 airs, 55 idles, 36mm vents, and no velocity stacks currently. Mixture screws are set 1.5 turns out. Its also hesitating from idle to around 3K rpm if I step on it hard like its flooding out. Time to put kits in the carbs? Does the jetting for the accelerator pump need to be changed or adjusted?
John |
   |
 
|
  |
Replies
| Brad Roberts |
Apr 13 2004, 09:42 PM
Post
#2
|
|
914 Freak! Group: Members Posts: 19,148 Joined: 23-December 02 Member No.: 8 Region Association: None |
Anything over Idle on that hole would be lean if anything was blocking the main jet.
Brett, I tried 55's in it and it would foul the plugs in no time flat. I'm down to 50's right now and it idles fine and starts perfect. Revs crisp with NO load and still stumbles on accel. I checked compression yesterday: 120-125 on every hole. Not great.. but not bad enough to cause any real issues. Next step is to check the valves. It sounds fine, but I realized it would not run correctly if they where tight. I'm getting a lot of reversion out of the velo stacks when I blip to wide open. Help. B |
|
|
|
Posts in this topic
stock93 Weber problem Apr 5 2004, 08:17 PM
ArtechnikA Racer Chris It is highly possible that the screw which holds t... Apr 5 2004, 10:04 PM 914ghost Does it drip while idling or with the engine off?
... Apr 5 2004, 10:10 PM Brad Roberts I have the SAME F-ing problem on a customers car r... Apr 5 2004, 11:49 PM stock93 Thanks brad. Its always comforting to know I'm... Apr 6 2004, 01:36 AM Racer Chris Brett W Welding the carb top will not be fun. Those casti... Apr 6 2004, 09:58 AM apoplexy "I have the SAME F-ing problem on a customers car ... Apr 6 2004, 02:12 PM RoadGlue Brad,
What does the exhaust gas analyzer show bel... Apr 6 2004, 11:33 PM Brad Roberts This is a tough issue with her car. I found two GR... Apr 7 2004, 01:07 AM apoplexy <... Apr 8 2004, 11:48 PM apoplexy richardL I was just playing with my carbs for my 2056. They... Apr 13 2004, 09:24 PM J P Stein I realize that this is a bit of apples and oranges... Apr 14 2004, 03:06 AM lapuwali I'm running 55 idles in 40IDFs with 28 vents o... Apr 14 2004, 09:11 AM
blabla914 I just went through the same thing on a T4 convers... Apr 14 2004, 10:01 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 4th July 2025 - 07:26 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.