 No spark! |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Steve73 |
  Jul 18 2011, 02:12 AM
Post
#1
|
|
Photographer/Shade Tree Mechanic  Group: Members Posts: 125 Joined: 2-July 11 From: Nashville Member No.: 13,269 Region Association: South East States  |
I'm trying to bring a dead 914 back to life. I have done the usual prep work and have hooked up the electrical system. The car turns over strongly but there is no spark! No spark at the plugs, no spark at the coil. I have switched the coil out with one I had laying around but i'm not getting any better results. Could it be the voltage regulator located in the box where the fuel injected controls are? (mine has been converted to dual carbs BTW).
What should I try next? Thanks in advance! |
   |
 
|
  |
Replies
| Steve73 |
Oct 7 2011, 03:23 PM
Post
#2
|
|
Photographer/Shade Tree Mechanic Group: Members Posts: 125 Joined: 2-July 11 From: Nashville Member No.: 13,269 Region Association: South East States |
I've got the engine running pretty well with the exception that I'm getting a fair amount of backfires. I've got the well set at 44 Degrees and the timing at about 35 btdc set at 3200rpm after i got the engine hot. How do I adjust for this. Is this because the carbs are running too rich? (Did i mention it's got carbs)
|
|
|
|
Posts in this topic
Steve73 No spark! Jul 18 2011, 02:12 AM
corsepervita How is the voltage up to the coil? The grounding?
... Jul 18 2011, 03:52 AM vsg914 Condensor Jul 18 2011, 05:01 AM Prospectfarms Unlikely you have two bad coils. A good coil may n... Jul 18 2011, 07:34 AM
Steve73
Unlikely you have two bad coils. A good coil may ... Jul 18 2011, 10:39 AM Drums66 ......Look at the grounding points, do them
coil ?... Jul 18 2011, 11:12 AM codemasterlax i have the same problem with mine not getting spar... Sep 20 2011, 02:25 PM Prospectfarms
i have the same problem with mine not getting spa... Sep 20 2011, 02:36 PM underthetire
i have the same problem with mine not getting spa... Sep 20 2011, 02:44 PM codemasterlax i do have in a bosch coil but wht bushings Sep 20 2011, 02:47 PM underthetire Grab the rotor and try and wiggle it side to side.... Sep 20 2011, 02:51 PM codemasterlax it does wiggle a lot but could tht also be because... Sep 20 2011, 02:56 PM underthetire
it does wiggle a lot but could tht also be becaus... Sep 20 2011, 03:06 PM codemasterlax ok what part exactly do i need to replace on the d... Sep 20 2011, 03:11 PM underthetire You would need to disassemble the dizzy, Press the... Sep 20 2011, 03:53 PM Cap'n Krusty And where is he going to find bushings? The wrong... Sep 20 2011, 05:05 PM Prospectfarms
And where is he going to find bushings? The wron... Sep 20 2011, 07:01 PM underthetire
And where is he going to find bushings? The wron... Sep 20 2011, 07:20 PM Prospectfarms
And where is he going to find bushings? The wro... Sep 20 2011, 09:12 PM Steve73 Prospect Farms Thanks for asking about my 914.
I ... Sep 21 2011, 01:56 AM underthetire
Prospect Farms Thanks for asking about my 914.
I... Sep 21 2011, 08:59 AM Steve73
[quote name='Steve73' post='1542174' date='Sep 21... Sep 25 2011, 09:53 PM vsg914 44 is the low side of the dwell. 47 would be bette... Oct 7 2011, 04:13 PM Prospectfarms Per: Pelican: timing with Carbs.
Set timing at 320... Oct 7 2011, 10:25 PM Steve73 Thanks everyone but I still need some advice about... Oct 7 2011, 11:48 PM Prospectfarms
Thanks everyone but I still need some advice abou... Oct 8 2011, 09:48 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 03:19 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.