 Cylinder boring, Sizes? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Black22 |
 Dec 13 2011, 06:28 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 886 Joined: 1-November 07 From: Creswell, OR Member No.: 8,290 Region Association: Pacific Northwest  |
I heard people here say that boring out your 94mm cylinders is probably a better bet than buying new, possibly sub-par due to metals used, cylinders. What about the 93mm cylinders? Would the cylinder walls be too thin? Am I wrong in assuming all cylinders are cast the same thickness and then bored out to specific sizes before distribution?
I have a 1.8 that I'm taking to a 1911. I was going to wait until the motor gave out. Well it still runs strong and is very peppy, but I just spun a rod bearing and she's knocking pretty bad after a decent drive. (IMG:style_emoticons/default/barf.gif) Already have a new crank ands pistons, just need to know if I have the Mahle 93mm stock cylinders, should I bore them out or buy new 96mm AA cylinders? |
   |
 
|
  |
Replies
| 76-914 |
Dec 14 2011, 08:53 PM
Post
#2
|
|
Repeat Offender & Resident Subaru Antagonist Group: Members Posts: 13,700 Joined: 23-January 09 From: Temecula, CA Member No.: 9,964 Region Association: Southern California 
|
QUOTE(Jake Raby @ Dec 13 2011, 07:49 PM)  Rimco did a good job with this before Todd left... Now I wouldn't send them a Briggs and Stratton to machine (IMG:style_emoticons/default/agree.gif) Word! |
|
|
|
| Black22 |
Dec 14 2011, 08:58 PM
Post
#3
|
|
Senior Member Group: Members Posts: 886 Joined: 1-November 07 From: Creswell, OR Member No.: 8,290 Region Association: Pacific Northwest |
QUOTE(76-914 @ Dec 14 2011, 06:53 PM) QUOTE(Jake Raby @ Dec 13 2011, 07:49 PM) Rimco did a good job with this before Todd left... Now I wouldn't send them a Briggs and Stratton to machine (IMG:style_emoticons/default/agree.gif) Word! (IMG:style_emoticons/default/av-943.gif) I just pictured you saying that with your Texas accent and it cracked me up! |
|
|
|
Posts in this topic
Black22 Cylinder boring Dec 13 2011, 06:28 PM
jcd914 1.8 cylinder should be fine to bore out for the 96... Dec 13 2011, 07:19 PM Jake Raby Boring cylinders requires a torque plate to mimic ... Dec 13 2011, 09:10 PM r_towle
I heard people here say that boring out your 94mm... Dec 13 2011, 09:39 PM Jake Raby Rimco did a good job with this before Todd left...... Dec 13 2011, 09:49 PM Cap'n Krusty Whatever you do, be sure to buy the correct piston... Dec 14 2011, 10:43 AM
Black22
Whatever you do, be sure to buy the correct pisto... Dec 14 2011, 11:14 AM Jake Raby
[quote name='76-914' post='1588915' date='De... Dec 14 2011, 10:13 PM Black22
[quote name='76-914' post='1588915' date='D... Dec 14 2011, 11:14 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 12:03 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.