 Lower Front Strut Ball Joint, Tapered Thread Stud removol |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| wndsnd |
  Jun 21 2012, 10:43 AM
Post
#1
|
|
You wanted a horse, but got a goat. Nobody wants a goat....  Group: Members Posts: 2,861 Joined: 12-February 12 From: North Shore, MA Member No.: 14,124 Region Association: North East States   |
(IMG:style_emoticons/default/headbang.gif)
I am really second thinking buying this car that lived in MAINE its whole life. Nothing is as it should be during dissasembly, and I am working with penetrants, heat, leverage, and will power and destroying almost everything coming off. I am now on replaceing the front struts and am at the lower ball joint. The Hayes manual calls for a hex nut or taperd thread stud. I think I have the later after removing the nut from one side. This stud I have map torched, and soaked with penetrant, and have pounded on with a mallet. looks like a little give on the other side but I don't think I am using the propers tools or technique. Any help or advise would be appreaciated... At this point it I am flatening the end of the stud. John Attached thumbnail(s)   
|
   |
 
|
  |
Replies
| r_towle |
Jun 21 2012, 02:09 PM
Post
#2
|
|
Custom Member Group: Members Posts: 24,705 Joined: 9-January 03 From: Taxachusetts Member No.: 124 Region Association: North East States 
|
oh,
Once you pull it out, dunk the whole stru into PB blaster for the night. They sell it by the gallon at Autozone. USe a plastic window washing jug and cut the top off...then dunk that in PB for a night or two. rich |
|
|
|
| wndsnd |
Jun 21 2012, 03:12 PM
Post
#3
|
|
You wanted a horse, but got a goat. Nobody wants a goat.... Group: Members Posts: 2,861 Joined: 12-February 12 From: North Shore, MA Member No.: 14,124 Region Association: North East States |
QUOTE(r_towle @ Jun 21 2012, 04:09 PM)  oh, Once you pull it out, dunk the whole stru into PB blaster for the night. They sell it by the gallon at Autozone. USe a plastic window washing jug and cut the top off...then dunk that in PB for a night or two. rich Got it out with a little finess ... see below, now I will soak the strut overnight. I assume that the strut now has to pull out of the arm? |
|
|
|
Posts in this topic
wndsnd Lower Front Strut Ball Joint Jun 21 2012, 10:43 AM
malaga_red75 John,
I just did this during my 5-lug conversion.... Jun 21 2012, 11:22 AM Dave_Darling My wife's SC has the same style ball joint. I... Jun 21 2012, 11:50 AM seanery so let me get this straight Dave, did you reuse th... Jun 21 2012, 11:53 AM FourBlades Taking the a-arm off the car makes it easier to ap... Jun 21 2012, 01:01 PM rhodyguy as fugly as that strut assem looks, i think you... Jun 21 2012, 01:02 PM wndsnd The ball joint will have to be replace by the time... Jun 21 2012, 01:29 PM r_towle You could take the lower nut off with a pipe wrenc... Jun 21 2012, 02:07 PM jmill I used an air hammer. You could also drill a hole... Jun 21 2012, 02:58 PM wndsnd Not the greatest example of a person with patience... Jun 21 2012, 03:09 PM r_towle ball joint is bolted from below the a-arm.
Its abo... Jun 21 2012, 03:26 PM jmill It looks like you have the correct replacement but... Jun 21 2012, 03:54 PM
TargaToy
Also I had better luck cutting off the round cast... Sep 25 2012, 05:54 PM infraredcalvin
Also I had better luck cutting off the round cas... Sep 25 2012, 09:44 PM jmill Oh, and then you'll need the special P tool to... Jun 21 2012, 04:02 PM wndsnd Thanks guys,
All great information and help. :b... Jun 21 2012, 06:19 PM Eric_Shea Remember my email about the MAP torch. Let's t... Jun 21 2012, 06:39 PM r_towle no special tools needed.
put the strut housing in ... Jun 21 2012, 06:49 PM wndsnd Rich
Now this is making sense. I thought the rep... Jun 21 2012, 07:03 PM cwpeden Ive always been a fan of the saying "Fire is ... Jun 21 2012, 07:08 PM wndsnd I had no luck withe the heat. Now that I have the... Jun 21 2012, 07:16 PM jmill You can use a pipe wrench, vice, chisel and a hamm... Jun 21 2012, 07:41 PM wndsnd Nice! Jun 21 2012, 07:46 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 11:59 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.