 Rear trunk Repair, a new twist |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| 76-914 |
  Jun 25 2012, 10:23 AM
Post
#1
|
|
Repeat Offender & Resident Subaru Antagonist  Group: Members Posts: 13,818 Joined: 23-January 09 From: Temecula, CA Member No.: 9,964 Region Association: Southern California 
 |
It's finally down after 8 weeks on the jack stands. Ugh! (IMG:style_emoticons/default/barf.gif). I know; it shouldn't have taken that long but I'm old and stupid so I have two good excuses for being slow. Most of this is McMarks fault. Just kidding. I had read a post where McMark describes how to check your CV's. Mine failed. (IMG:style_emoticons/default/headbang.gif) So, I ordered a set of CV's. Then that damned Otto posted these in the classified WTS:
 Since it was on jack stands and my trunk looked like this I decided to repair the trunk while it was up.  As I began fitting the rear panel piece I noticed the similarity between the rear panel and the piece in front of the trunk spar/brace and thought, maybe...... Then the G&R event happened and found another one of these panels ($5 cheaper than the one I bought from Otto) so I bought it, too! I said too because I also bought a set of Fuch's (IMG:style_emoticons/default/wub.gif) Sure enough, after a few measurements and "trim to fit" I was able to "sneak" this rear panel piece into the front.  The slits were intentional to allow the piece to slid between.  This is one place that it didn't match. Notice the gap between the new piece and the brace. It's a gap appx. 15mm  |
   |
 
|
  |
Replies
| ThePaintedMan |
Jun 25 2012, 12:55 PM
Post
#2
|
|
Advanced Member Group: Members Posts: 3,887 Joined: 6-September 11 From: St. Petersburg, FL Member No.: 13,527 Region Association: South East States
|
Couple questions. Since this isn't load bearing, its just spot welded in, correct? Thats what it looks like. Makes sense.
Also, has anyone else used those new CV boots from Pelican? Mine had 2 blank bolt holes in them, like his. Do you plan on sealing them? I used nylon bolts from Home Depot, which seems to be working for now. Wood floors SUCKKKKKK! I had to do a whole downstairs in bamboo tongue and grove once. My knees and back have never hurt so bad (no sick jokes) |
|
|
|
Posts in this topic
76-914 Rear trunk Repair Jun 25 2012, 10:23 AM
76-914 Here is the other side "beaten" into sub... Jun 25 2012, 10:50 AM 76-914 So what in the Hell was I doing the rest of the ti... Jun 25 2012, 10:58 AM 76-914 Geez, I almost forgot the "money shot". ... Jun 25 2012, 11:14 AM
xsJerry Nice job on the trunk. I just cut out a piece of 1... Jun 25 2012, 10:05 PM SLITS Now you can trap water again.
Good job Kent (at l... Jun 25 2012, 11:26 AM 76-914
Couple questions. Since this isn't load beari... Jun 25 2012, 03:32 PM ThePaintedMan
Those extra holes should have the dowel pins ins... Jun 25 2012, 07:40 PM 76-914 Now I got it. I usually have to dig out old grease... Jun 25 2012, 09:54 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 14th November 2025 - 06:59 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.