 Engine bar mounts are bent backwards, Engine mount |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Erben914 |
 Jan 13 2013, 02:52 PM
Post
#1
|
|
Member  Group: Members Posts: 137 Joined: 1-January 13 From: Sacramento Member No.: 15,314 Region Association: Central California  |
Hey guys I need some advice. My engine bar is bent backwards towards the rear of the car. The bar itself looks fine, but the two bolts are angled about 60 degrees instead of 90. My shift linkage is rubbing but isn't causing any problems.
My question is... Should I use a big pry bar and bent it back to vertical or do I need to drop the bar and do something at the mount area? I don't want to weaken the bolts or the mounts more. Are the mounts rubber and they just need to be re seated? Thanks for any help |
   |
 
|
  |
Replies
| last337 |
Jan 13 2013, 04:45 PM
Post
#2
|
|
Member Group: Members Posts: 421 Joined: 4-December 12 From: New Orleans Member No.: 15,221 Region Association: None |
I have the exact same problem and have been thinking about best way to fix. I figure if u try to turn either bolt they will snap. I thought possibly I could jack up engine to hold in place then grind off bolt heads and remove mount bar then back out remains of bolts. Any other ideas?
 |
|
|
|
| reharvey |
Jan 13 2013, 06:06 PM
Post
#3
|
|
Senior Member Group: Members Posts: 573 Joined: 16-July 08 From: N. E. Ohio Member No.: 9,308 Region Association: North East States |
QUOTE(last337 @ Jan 13 2013, 05:45 PM)  I have the exact same problem and have been thinking about best way to fix. I figure if u try to turn either bolt they will snap. I thought possibly I could jack up engine to hold in place then grind off bolt heads and remove mount bar then back out remains of bolts. Any other ideas? Wow this looks bad--is the motor mount nut welded to the bar? |
|
|
|
Posts in this topic
Erben914 Engine bar mounts are bent backwards Jan 13 2013, 02:52 PM
brant you drug over a parking curb / trailer / or someth... Jan 13 2013, 02:57 PM
Erben914
you drug over a parking curb / trailer / or somet... Jan 13 2013, 03:21 PM brant just be careful if you pry against anything.
the ... Jan 13 2013, 03:22 PM sixnotfour speed bump backwards should do it.. Jan 13 2013, 03:25 PM rgalla9146
speed bump backwards should do it..
Tail shift... Jan 13 2013, 04:38 PM draganc
speed bump backwards should do it..
LMFAO. :ro... Jan 14 2013, 07:25 PM reharvey The brackets the bolts go though may also be bent. Jan 13 2013, 04:09 PM stugray We need to know what year.
The motor mounts are di... Jan 13 2013, 04:28 PM Spoke I recently had to remove the engine bar to do some... Jan 13 2013, 06:54 PM last337
I recently had to remove the engine bar to do som... Jan 13 2013, 07:00 PM last337
I recently had to remove the engine bar to do som... Jan 13 2013, 07:00 PM ottox914 Better pics would help. Sounds like you are on th... Jan 13 2013, 07:23 PM Dave_Darling The big bolts are already eff'ed, so go ahead ... Jan 13 2013, 09:35 PM Valy I have a good engine bar for you for free. Just co... Jan 13 2013, 10:31 PM McMark Best way to completely remedy this issue:
1. supp... Jan 14 2013, 12:13 PM euro911 It would take a lot to bend a cast iron engine bar... Jan 14 2013, 12:35 PM last337
It would take a lot to bend a cast iron engine ba... Jan 14 2013, 12:58 PM JawjaPorsche
It would take a lot to bend a cast iron engine b... Jan 14 2013, 01:15 PM last337 I have a '73 2.0 so I guess that means it is a... Jan 14 2013, 01:19 PM JawjaPorsche
I have a '73 2.0 so I guess that means it is ... Jan 14 2013, 01:22 PM last337
I have a '73 2.0 so I guess that means it is... Jan 14 2013, 02:15 PM euro911 I have a '73 2.0 so I guess that means it is a... Jan 14 2013, 07:18 PM last337
I have a '73 2.0 so I guess that means it is ... Jan 14 2013, 07:29 PM McMark
That's what I thought. But I had one that wa... Jan 14 2013, 05:26 PM The Cabinetmaker I've seen this on lots of cars. It's almos... Jan 14 2013, 05:27 PM last337 Well upon closer inspection it appears To be the e... Jan 14 2013, 07:24 PM euro911 RE: Engine bar mounts are bent backwards Jan 14 2013, 10:38 PM |
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 10th May 2025 - 01:06 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.