 Re-bushing my side shifter, drilling etc. |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| pbob42 |
 Feb 9 2013, 01:45 PM
Post
#1
|
|
Newbie  Group: Members Posts: 46 Joined: 6-June 12 From: san diego Member No.: 14,531 Region Association: None  |
Replacing the firewall and shiftrod bushings. PO stripped out the set screws 20 years ago and left the project undone. I am drilling out the set screws but the linkage is locked together at both set screw locations (rear and firewall).
Any suggestions on getting this linkage apart? |
   |
 
|
  |
Replies
| rhodyguy |
Feb 12 2013, 12:14 PM
Post
#2
|
|
Chimp Sanctuary NW. Check it out. Group: Members Posts: 22,240 Joined: 2-March 03 From: Orion's Bell. The BELL! Member No.: 378 Region Association: Galt's Gulch |
if you think the set screw situation is hopeless, post a WTB for the rods. they shouldn't that expensive. cut the rear bar forward of where it enters the console and behind the behind the front coupler. remove the shifter from the the front rod and pull the rod out. i personally can only spend so much time fighting an issue that can be fixed with a little dough.
|
|
|
|
| pbob42 |
Feb 12 2013, 12:20 PM
Post
#3
|
|
Newbie Group: Members Posts: 46 Joined: 6-June 12 From: san diego Member No.: 14,531 Region Association: None |
first fire then hacksaw. Got it.
|
|
|
|
Posts in this topic
pbob42 Re-bushing my side shifter, drilling etc. Feb 9 2013, 01:45 PM
timothy_nd28 :sawzall: and post a WTB ad in the classified sec... Feb 9 2013, 02:13 PM wildman you might try shifting into a forward gear (like 2... Feb 9 2013, 02:45 PM
pbob42
you might try shifting into a forward gear (like ... Feb 9 2013, 05:51 PM brant a bigger drill bit
I've had to do it one
I to... Feb 9 2013, 05:59 PM rhodyguy try going thru the access cover (center tunnel, un... Feb 9 2013, 06:08 PM flash914 Left hand drill bits PB blaster and heat. Feb 9 2013, 06:54 PM rhodyguy the set screws have a nub on the end that go into ... Feb 9 2013, 07:05 PM euro911 I would try penetrating oil and an easy-out first.... Feb 9 2013, 09:59 PM pbob42 Got off track - had to put a starter in my daughte... Feb 12 2013, 11:05 AM worn
Got off track - had to put a starter in my daught... Feb 12 2013, 11:30 AM pbob42 I've been working at the back. I will see if ... Feb 12 2013, 12:08 PM euro911 If the PO used RED lock-tite, it's gonna be t... Feb 12 2013, 01:00 PM rhodyguy what's a hacksaw? :D power tools. Feb 12 2013, 01:18 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 11th May 2025 - 11:40 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.