 Injector Click Test (outside of motor) |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| lsintampa |
 Aug 11 2013, 10:20 AM
Post
#1
|
|
Senior Member  Group: Members Posts: 520 Joined: 28-January 13 From: Tampa, FL Member No.: 15,441 Region Association: South East States  |
OK,
I hooked up a pig-tail to this injector. Then I got a 9V battery and tapped the pig-tail numerous times. I never hear the injector click - and I'm assuming that it should. The pig-tail does spark though - as if there is a short - which seems odd. So, what is that telling me? BTW - PO has said that all the injectors were cleaned and tested and all tested and sprayed well. They were however sitting in a baggy for three months. I can't imagine that they just went south???? All four injectors and the cold start valve all behave the same way. Thanks, Len  Attached thumbnail(s) 
|
   |
 
|
  |
Replies
| JeffBowlsby |
Aug 12 2013, 10:40 AM
Post
#2
|
|
914 Wiring Harnesses & Beekeeper Group: Members Posts: 8,907 Joined: 7-January 03 From: San Ramon CA Member No.: 104 Region Association: None 
|
I have seen this before. The injectors must be installed and put into service right away or they can freeze-up again. No worries, just get them recleaned, they should work again. If you have paperwork for the shop that did them before, they may be willing to redo them at no charge.
|
 |
|
Posts in this topic
lsintampa Injector Click Test (outside of motor) Aug 11 2013, 10:20 AM
reharvey These operate at 3 volts. I use a DC model train t... Aug 11 2013, 11:21 AM toadman They do operate at 3V but, in the past I have test... Aug 11 2013, 11:31 AM lsintampa OK,
So there is NO click under power.
They ohm ... Aug 11 2013, 11:46 AM Mark Henry If the pintle won't budge after the soaking (i... Aug 11 2013, 12:00 PM r_towle Dude, you have three threads going for the same pr... Aug 11 2013, 02:56 PM
lsintampa
Dude, you have three threads going for the same p... Aug 11 2013, 09:04 PM Porsche930dude try some different test leads and a different batt... Aug 11 2013, 06:24 PM lsintampa Soaked overnight - no change.
I spoke with the PO... Aug 12 2013, 10:22 AM speed metal army Is the pigtail you made any good? Just a thought..... Aug 12 2013, 10:41 AM lsintampa
Is the pigtail you made any good? Just a thought.... Aug 12 2013, 11:00 AM lsintampa OK,
Another question that I don't have an ans... Aug 12 2013, 11:13 AM SLITS The electrical component inside is a solenoid. It... Aug 12 2013, 11:19 AM lsintampa
The electrical component inside is a solenoid. I... Aug 12 2013, 11:26 AM Jeff Bowlsby You can hear a click when activated. Seems to me ... Aug 12 2013, 11:41 AM lsintampa
You can hear a click when activated. Seems to me... Aug 12 2013, 11:52 AM Jeff Bowlsby
You can hear a click when activated. Seems to m... Aug 12 2013, 12:59 PM timothy_nd28 Consider reading this thread, he went thru the sam... Aug 12 2013, 01:00 PM r_towle did you soak them?
If so, what did you soak them i... Aug 12 2013, 01:14 PM lsintampa
did you soak them?
If so, what did you soak them ... Aug 12 2013, 01:51 PM pcar916 My 993 injectors were all frozen when I got the en... Aug 12 2013, 01:16 PM lsintampa
My 993 injectors were all frozen when I got the e... Aug 12 2013, 01:55 PM Jeff Bowlsby They are obviously stuck closed. Send them in for... Aug 12 2013, 01:59 PM lsintampa
They are obviously stuck closed. Send them in fo... Aug 12 2013, 02:11 PM luskesq
They are obviously stuck closed. Send them in f... Aug 12 2013, 04:13 PM lsintampa
[quote name='lsintampa' post='1908174' date='Aug ... Aug 12 2013, 06:52 PM timothy_nd28 You should try installing a grease zerk on each in... Aug 12 2013, 02:09 PM r_towle All a professional will do is soak them.
If they w... Aug 12 2013, 04:39 PM Valy I'm not sure Techtron will work.
I used an ult... Aug 12 2013, 06:15 PM SLITS Inside the fuel inlet, there is a micro-screen to ... Aug 12 2013, 10:12 PM lsintampa Let's end this...
I'm beyond guessing wh... Aug 13 2013, 09:50 AM worn
Let's end this...
I'm beyond guessing w... Aug 13 2013, 12:39 PM lsintampa Yeah, the shop just called.
Two ultrasonic baths ... Aug 13 2013, 12:57 PM Jeff Bowlsby Great way of looking at it Len. Lemonade from lem... Aug 13 2013, 01:10 PM Bob L. Have you licked that 9v battery lately? You sure i... Aug 13 2013, 03:11 PM stugray
my thoughts exactly.
We have similar "valv... Aug 13 2013, 03:31 PM worn
my thoughts exactly.
We have similar "val... Aug 16 2013, 11:02 AM Valy Oh... I got some captures.
Ping me if I forget to ... Aug 13 2013, 03:53 PM lsintampa For those following the drama.
The shop couldn... Aug 14 2013, 09:36 AM aircooledtechguy I just went through this on a friends car that use... Aug 14 2013, 11:31 PM lsintampa
I just went through this on a friends car that us... Aug 15 2013, 08:47 AM jsconst Len, I just sent in 8 - 2.0 injectors for cleaning... Aug 14 2013, 11:51 PM lsintampa
Len, I just sent in 8 - 2.0 injectors for cleanin... Aug 15 2013, 07:06 AM jsconst That would be sweet if you find them, good luck.
... Aug 15 2013, 07:14 AM aircooledtechguy :thumbsup: Aug 15 2013, 09:25 PM Valy Finally got to upload this.
This is the power at ... Aug 16 2013, 02:32 PM r_towle Cool, but where is the voltage? Aug 16 2013, 04:34 PM Valy
Cool, but where is the voltage?
The voltage is t... Aug 16 2013, 05:08 PM stugray Valy,
Thanks for the scope capture.
It sure looks... Aug 16 2013, 10:41 PM Valy
Valy,
Thanks for the scope capture.
It sure look... Aug 16 2013, 11:47 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 09:38 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.