 Front End Bracing |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| 57lincolnman |
 Aug 17 2013, 08:41 PM
Post
#1
|
|
Member  Group: Members Posts: 174 Joined: 14-September 10 From: Los Angeles Member No.: 12,175 Region Association: Southern California  |
My 75 has a dealer installed a/c unit. The lower pan in the front trunk was cut out years ago by the dealer. Has anyone tried to fabricate cross bracing to tighten the front end? I think the structural integrity of the unibody was compromised by this "dealer authorized" surgical procedure. Interested in your thoughts. Thanks.
|
   |
 
|
  |
Replies
| rhodyguy |
Aug 18 2013, 08:27 AM
Post
#2
|
|
Chimp Sanctuary NW. Check it out. Group: Members Posts: 22,252 Joined: 2-March 03 From: Orion's Bell. The BELL! Member No.: 378 Region Association: Galt's Gulch |
cracks can result that run towards the front control arm mounting points. plus there are bunch of holes for the hoses that would have to be welded up and in most cases the pass side engine shelve gets butchered. as noted installs vary. somewhat clean to out right dog crap.
|
|
|
|
Posts in this topic
57lincolnman Front End Bracing Aug 17 2013, 08:41 PM
messix if it's just the sheet metal behind the front ... Aug 17 2013, 08:50 PM
57lincolnman
if it's just the sheet metal behind the front... Aug 17 2013, 08:57 PM 57lincolnman
if it's just the sheet metal behind the front... Aug 17 2013, 08:59 PM
messix
if it's just the sheet metal behind the fron... Aug 17 2013, 09:22 PM SirAndy it should be ok.
I dis-agree ...
I think any cut... Aug 17 2013, 09:42 PM messix I think the only forces put on that section is hor... Aug 17 2013, 09:56 PM FourBlades Restoration Design just started making a perfect p... Aug 17 2013, 10:01 PM messix
Restoration Design just started making a perfect ... Aug 17 2013, 10:05 PM FourBlades
Restoration Design just started making a perfect... Aug 17 2013, 10:08 PM messix I just went out to put my '75 back in the gara... Aug 17 2013, 10:24 PM Racer Chris
...if it's just a street car I don't thin... Aug 18 2013, 07:38 AM 914Sixer Yes, 75-76 do have a little more structure to them... Aug 18 2013, 06:44 AM jimkelly comparision Aug 18 2013, 06:57 AM 57lincolnman I have invested quite a bit to have working a/c, s... Aug 18 2013, 10:24 AM Racer Chris
I have invested quite a bit to have working a/c, ... Aug 18 2013, 04:44 PM zambezi Heres what I did. Not sure if it added any struct... Aug 18 2013, 11:54 AM Larry Hubby If you've ever looked at the floor of the fron... Aug 18 2013, 06:01 PM sean_v8_914 if anyone has evidence of stresses in this area, p... Aug 18 2013, 07:58 PM Krieger When I started to take my 75, that had A/C, apart ... Aug 18 2013, 08:25 PM Racer Chris This car had the full trunk floor intact.
Cracks o... Aug 19 2013, 07:37 AM Eric_Shea :agree: I've seen pictures of a bad bushing li... Aug 19 2013, 08:56 AM sean_v8_914 right along th spot weld line Aug 19 2013, 10:27 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 31st August 2025 - 08:19 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.