 Ride height and front to back balance, Rear currently sits about 1/2-3/4" lower than front |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| DRPHIL914 |
 Mar 20 2014, 07:17 AM
Post
#1
|
|
Dr. Phil  Group: Members Posts: 5,874 Joined: 9-December 09 From: Bluffton, SC Member No.: 11,106 Region Association: South East States 
 |
couple questions and looking for guidance on solution-
currently here is what is on the car - Rear: has new sport bilistien shocks and new 100# springs. spring perches are set right in the middle currently, 4th from the bottom, i think there are 3 more slots above that. Front: i have no idea- stock shocks etc, seem fine and no need to change them out. have not check to see if ride height etc is where it should be. I just completed putting all new 5 lug on front and back, with new calipers, brake lines, bearings etc etc., but now am going to put new turbo tie rods on. Once this is complete i was going to take it to local shop to have alignment done. They are fully familar with all older 911 air cooled , owner has a bunch of his own, so i guess he should be familar with the adjusting proceedure for the height balance? - i could move the rear spring perches up one or two spots but then it may make it a bit bouncy-more spring than shock. anyway any advice and direction also for threads that show how to measure these things would be helpful. Attached thumbnail(s) 
|
   |
 
|
  |
Replies
| mittelmotor |
Mar 20 2014, 10:01 AM
Post
#2
|
|
Member Group: Members Posts: 334 Joined: 21-May 12 From: SoCal Member No.: 14,464 Region Association: None |
Are you measuring ride height from the bottom edge of the rockers, or somewhere else?
Ride height/rake is pretty subjective, but I think the 914 looks good riding level or ever-so-slightly nose high, which is what you have now. If you raise the rear ride height slightly, it won't make it any more bouncy…you're not changing the damping, just moving the perch relative to the shock body. You could always lower the front and leave the rear alone…it's just a matter of turning the splined adjusters. |
|
|
|
Posts in this topic
Philip W. Ride height and front to back balance Mar 20 2014, 07:17 AM
monkeyboy A corner balance\height adjustment has nothin... Mar 20 2014, 09:32 AM
malcolm2
Are you measuring ride height from the bottom edg... Mar 24 2014, 11:07 AM Chris H. A pic would help but what you're describing so... Mar 20 2014, 10:54 AM Philip W.
A pic would help but what you're describing s... Mar 20 2014, 12:33 PM bulitt Been a while but I think I read (in haynes?) or th... Mar 20 2014, 11:58 AM Philip W.
Been a while but I think I read (in haynes?) or t... Mar 20 2014, 12:29 PM 914_teener
Been a while but I think I read (in haynes?) or t... Mar 20 2014, 01:10 PM Philip W. Finally took a picture. Pretty close to stock. Whe... Mar 24 2014, 09:51 AM mittelmotor
Finally took a picture. Pretty close to stock. Wh... Mar 24 2014, 10:06 AM Chris H. :agree: Looks fine as is but you can level it eas... Mar 24 2014, 10:55 AM Philip W.
:agree: Looks fine as is but you can level it ea... Mar 24 2014, 11:15 AM Travis Neff I did a 1/2 inch rake down on the front, measured ... Mar 24 2014, 12:52 PM Philip W.
I did a 1/2 inch rake down on the front, measured... Mar 24 2014, 08:13 PM bandjoey To lower the front...Looking at the bolt head on..... Mar 24 2014, 09:01 PM jcd914
To lower the front...Looking at the bolt head on.... Mar 25 2014, 01:02 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 7th December 2025 - 11:36 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.