 914/6 oil leak, Case stud question |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| bcheney |
 Oct 12 2014, 12:53 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,341 Joined: 16-November 03 From: Orlando, FL Member No.: 1,348 Region Association: South East States  |
I have an original 6 engine in my 6 conversion car. I have an oil leak at the stud circled in the pic below. I have tried to torque the nut on this stud without success. I then double nutted the stud to see if maybe the stud and become loose. I was able to turn the stud in a bit so I thought I was making progress. When I removed the double nuts and placed a washer and nut back on to torque to value it won't snug up. Instead, as I torque the nut...the stud begins to turn out. I have a bad feeling about this....Please chime in with your wisdom.
Attached image(s) 
|
   |
 
|
  |
Replies
| carr914 |
Oct 29 2014, 06:27 AM
Post
#2
|
|
Racer from Birth Group: Members Posts: 126,537 Joined: 2-February 04 From: Tampa,FL Member No.: 1,623 Region Association: South East States  |
Did you send the picture to Mike?
Tell Leslie she can't drive anything Air-Cooled for a Month! |
 |
|
Posts in this topic
bcheney 914/6 oil leak Oct 12 2014, 12:53 PM
Luke M By the sounds of things the stud is pulling from t... Oct 12 2014, 12:59 PM
bcheney
By the sounds of things the stud is pulling from ... Oct 12 2014, 01:25 PM Luke M
By the sounds of things the stud is pulling from... Oct 12 2014, 02:28 PM Mark Henry
. You may try the epoxy route but I don't thi... Oct 12 2014, 02:43 PM Mark Henry Clean it up real good to bare metal, degrease it a... Oct 12 2014, 02:08 PM GeorgeRud I had the same thing happen to me many years ago. ... Oct 12 2014, 02:13 PM bcheney
I had the same thing happen to me many years ago.... Oct 12 2014, 02:37 PM rfuerst911sc Brian sorry to hear I don't visit here often s... Oct 12 2014, 02:46 PM johnhora Sorry to say I have had that same problem and noth... Oct 12 2014, 05:45 PM Cap'n Krusty I fixed one without taking the engine apart. Bore... Oct 12 2014, 06:24 PM bcheney
I fixed one without taking the engine apart. Bor... Oct 12 2014, 06:49 PM sixnotfour brake clean the hole see if you can grab a few thr... Oct 12 2014, 06:51 PM bcheney
brake clean the hole see if you can grab a few th... Oct 29 2014, 05:22 AM Luke M
It depends if you are taking the engine apart a... Oct 29 2014, 07:59 AM bcheney Ok I removed the stud just a little while ago and ... Oct 29 2014, 09:40 AM Luke M That doesn't look good.. It's time to spli... Oct 29 2014, 12:00 PM bob I had the same thing. I cleaned out the stripped t... Oct 29 2014, 12:36 PM bcheney
I had the same thing. I cleaned out the stripped ... Oct 29 2014, 01:10 PM gereed75
I had the same thing. I cleaned out the stripped... Oct 29 2014, 01:22 PM bcheney
[quote name='bcheney' post='2104066' date='Oct 29... Oct 29 2014, 04:04 PM bob I forget where I found the tap. (maybe McMasterCar... Oct 29 2014, 01:40 PM bcheney
I forget where I found the tap. (maybe McMasterCa... Oct 29 2014, 04:05 PM bob yeah. I measured the original stud and the hole. t... Oct 29 2014, 05:42 PM gereed75 sorry I did not post sooner. Just got to the shop... Nov 1 2014, 08:53 AM bcheney
sorry I did not post sooner. Just got to the sho... Nov 1 2014, 03:16 PM bcheney
yeah. I measured the original stud and the hole. ... Nov 2 2014, 10:04 PM bcheney
yeah. I measured the original stud and the hole. ... Nov 6 2014, 06:17 AM gereed75 Never thought that the threads might go deeper. It... Nov 1 2014, 05:07 PM wndsnd Not sure the threads are deeper but I do think the... Nov 1 2014, 05:19 PM sixnotfour http://www.mcmaster.com/#99067A248
you cut to cut... Nov 2 2014, 10:20 PM sixnotfour darn double post :beer2: Nov 2 2014, 10:23 PM bob that sux... sorry to hear that the depth is differ... Nov 6 2014, 06:55 AM bcheney
that sux... sorry to hear that the depth is diffe... Nov 6 2014, 09:15 AM gereed75 I had a chance to pull this stud yesterday. The de... Nov 9 2014, 09:32 AM bcheney
I had a chance to pull this stud yesterday. The d... Nov 9 2014, 05:26 PM Luke M
[quote name='gereed75' post='2108416' date='Nov 9... Nov 9 2014, 06:10 PM gereed75 I have a couple of Ideas depending on what all I d... Nov 9 2014, 06:15 PM gereed75 Bcheney, check your PM's. And I see from pre... Nov 14 2014, 11:07 AM mepstein Get a pro to time sert. See what Joe O'brien c... Nov 6 2014, 07:23 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 1st August 2025 - 07:11 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.