 I need to fix and replace some bad wiring(melted) near the fuse box, **Update 11/6 - installed j-west fuse box * started! woo hoo! |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| DRPHIL914 |
 Nov 5 2014, 07:37 AM
Post
#1
|
|
Dr. Phil  Group: Members Posts: 5,955 Joined: 9-December 09 From: Kennesaw, GA Member No.: 11,106 Region Association: South East States 
 |
I am installing the new Jwwest fuse box and
I have a 3" section of wire off the #5 back row fuse that has melted insulation(grey with black stripe) what is the best way to replace and splice in the new piece and what gauge wire is correct? |
   |
 
|
  |
Replies
| 76-914 |
Nov 7 2014, 07:53 AM
Post
#2
|
|
Repeat Offender & Resident Subaru Antagonist Group: Members Posts: 13,920 Joined: 23-January 09 From: Temecula, CA Member No.: 9,964 Region Association: Southern California
|
12volts at the coil with key on? Do it quickly. Remember that ign module doesn't like power to it when the engine isn't running.
|
|
|
|
| DRPHIL914 |
Nov 7 2014, 09:59 AM
Post
#3
|
|
Dr. Phil Group: Members Posts: 5,955 Joined: 9-December 09 From: Kennesaw, GA Member No.: 11,106 Region Association: South East States
|
QUOTE(76-914 @ Nov 7 2014, 08:53 AM)  12volts at the coil with key on? Do it quickly. Remember that ign module doesn't like power to it when the engine isn't running. i will check this tonight, then i'll go thur each plug and plug wire, cap rotor etc check for shorts etc. those wires are fairly new, and plugs were brand new right before going up to Octeenerfest. Its getting gas so it has to be something somewhere in the ignition harness/spark/coil/wires/distributor/ecu |
|
|
|
Posts in this topic
Philip W. I need to fix and replace some bad wiring(melted) near the fuse box Nov 5 2014, 07:37 AM
bdstone914
I am installing the new Jwwest fuse box and
I h... Nov 5 2014, 09:38 AM type47
... to replace and splice in the new piece ...
I... Nov 5 2014, 10:15 AM Philip W. Circuit board in place with a few new connectors a... Nov 5 2014, 09:21 PM
Philip W.
Circuit board in place with a few new connectors ... Nov 7 2014, 07:24 AM
billh1963
Circuit board in place with a few new connectors ... Nov 7 2014, 08:35 AM Philip W.
Circuit board in place with a few new connectors... Nov 7 2014, 09:56 AM Philip W.
Circuit board in place with a few new connectors... Nov 7 2014, 12:53 PM Dave_Darling Tape an extra spark plug to a ground, and plug in ... Nov 7 2014, 10:58 AM Philip W.
Tape an extra spark plug to a ground, and plug in... Nov 7 2014, 12:49 PM Racer Chris Some of the fuse circuits in the old panel are bri... Nov 7 2014, 11:14 AM Philip W.
Some of the fuse circuits in the old panel are br... Nov 7 2014, 12:42 PM Racer Chris
do you know which circuits have this?
:idea:
T... Nov 7 2014, 01:44 PM Jeff Bowlsby Wait.
It worked before the fuse panel swap, and ... Nov 7 2014, 01:06 PM Tom You are getting lost in " OMG, what is wrong... Nov 7 2014, 02:45 PM Philip W. So this morning I took Tom's advice and starte... Nov 8 2014, 10:01 AM Mike Bellis Glad you got it running.
For the record, the igni... Nov 8 2014, 10:19 AM Tom Glad I was able to get you to stop and think for a... Nov 8 2014, 02:49 PM Philip W. Turns out since tje battery was disconnected I nee... Nov 8 2014, 10:32 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 27th July 2026 - 08:03 AM |
Invision Power Board
v9.1.4 © 2026 IPS, Inc.