 Replacing Oil Cooler Seals, Engine out, this should be easy, right? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| BeatNavy |
 Mar 7 2015, 06:11 PM
Post
#1
|
|
Certified Professional Scapegoat  Group: Members Posts: 2,962 Joined: 26-February 14 From: Easton, MD Member No.: 17,042 Region Association: MidAtlantic Region 
 |
Ok, this should be easy. I have the engine sitting on a dolly, and I'm trying to figure out where I access the oil cooler seals so I can replace them while the engine's out. I know they are on the vertical side of the cooler, and probably on the inside (not outside) side of the cooler, right? Getting access under the engine is a little difficult since it's on the dolly and I currently don't have a good view up directly underneath. What do I need to remove in order to get access to those seals? Should I attack it from the top or from underneath? I started to remove the oil filter housing but the top nut is pretty well hidden too...
|
   |
 
|
  |
Replies
| TheCabinetmaker |
Mar 8 2015, 05:09 PM
Post
#2
|
|
I drive my car everyday Group: Members Posts: 8,373 Joined: 8-May 03 From: Tulsa, Ok. Member No.: 666 |
Your missing two little flat pieces of metal that screw to the shroud and hold the rod in place. They are about 3/4" wide and 1 1/4" long with the corners knocked off at a45, but easy to make them, or get a couple of flat mending plates at the hardware store. Alternator boot is available new at the bughaus. It's the same as a van with a type 4.
|
 |
|
Posts in this topic
BeatNavy Replacing Oil Cooler Seals Mar 7 2015, 06:11 PM
mepstein One or 2 pieces of engine tin and the right size w... Mar 7 2015, 06:59 PM
BeatNavy
One or 2 pieces of engine tin and the right size ... Mar 7 2015, 07:04 PM Dave_Darling Just remove the fan and fan shroud. Three bolts (... Mar 7 2015, 07:40 PM BeatNavy Sweet, thanks Dave. That must be the "trick.... Mar 7 2015, 07:47 PM Larmo63 The front of the motor is like a big puzzle. It lo... Mar 8 2015, 12:09 AM bandjoey http://www.pelicanparts.com/techarticles/9...ooler... Mar 8 2015, 10:53 AM r_towle Yup, remove fan, fan housing, alternator.
Oil cool... Mar 8 2015, 01:44 PM BeatNavy Cool, thanks for the comments, gentlemen.
Yup, t... Mar 8 2015, 04:06 PM r_towle Grease gun hose or paint ball gun hose
Rich Mar 8 2015, 04:16 PM BeatNavy
Grease gun hose or paint ball gun hose
Rich
Ok,... Mar 8 2015, 04:26 PM BeatNavy Here's the engine tin after powdercoating. No... Mar 8 2015, 04:28 PM BeatNavy
Your missing two little flat pieces of metal that... Mar 8 2015, 05:14 PM BeatNavy Never mind. I see it on my other car. Thanks Cur... Mar 8 2015, 05:49 PM Stltri Reviving an old thread.
Can someone confirm the ... Feb 14 2022, 07:35 PM BeatNavy Dayummm... this is an old thread. I had forgotten... Feb 14 2022, 07:47 PM Stltri
Dayummm... this is an old thread. I had forgotte... Feb 14 2022, 08:06 PM 914Mels It looks like the remote hose has straight threads... Feb 14 2022, 11:28 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 2nd April 2026 - 02:24 PM |
Invision Power Board
v9.1.4 © 2026 IPS, Inc.