 Shifter springs re-install, is there an easy way ? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| pgollender |
 Apr 26 2015, 11:28 PM
Post
#1
|
|
Member  Group: Members Posts: 201 Joined: 5-July 11 From: Sacramento Member No.: 13,281 Region Association: Northern California  |
I decided to replace the ball socket on my 1970 shifter . I didn't realize the plate springs were under so much tension. I haven't found a way to put them back.
Any body have an idea ?  |
   |
 
|
  |
Replies
| malcolm2 |
Apr 30 2015, 09:51 AM
Post
#2
|
|
Advanced Member Group: Members Posts: 2,747 Joined: 31-May 11 From: Nashville Member No.: 13,139 Region Association: South East States 
|
Glad you did this. And has been the case with my car.... do it once to learn how. Then do it again. I have done lots of things more than once. You get done, then say, "CRAP" and do it again.
Hey, in post 10 where you can see your front wheel. I see a stack of cinder blocks. Are they holding up your car? Cinder blocks are designed to be used with the holes vertical, not horizontal. You never see a Karate guy smash a block by hitting the top of the block.... always the side. You never see a whole building built with the holes showing either. Becareful. |
|
|
|
Posts in this topic
pgollender Shifter springs re-install Apr 26 2015, 11:28 PM
Old Yella
I decided to replace the ball socket on my 1970 ... Apr 26 2015, 11:54 PM mepstein Leather gloves. Safety glasses vise grips. I used ... Apr 27 2015, 04:09 AM jim_hoyland There is an easy way, i recently did it. Forget ex... Apr 27 2015, 04:49 AM saigon71 Oh yeah...good times with those springs!
I pu... Apr 27 2015, 05:55 AM maf914 It can be done, but what a pain! I launched t... Apr 27 2015, 07:03 AM rhodyguy Put one end of a spring near a hole. Push one of t... Apr 27 2015, 07:22 AM bdstone914 Cap'n Krusty replied to a thread explaining to... Apr 27 2015, 07:22 AM Brian_Boss First off, if you are not holding the housing in a... Apr 27 2015, 09:55 AM
r_towle
First off, if you are not holding the housing in ... Apr 30 2015, 03:02 PM pgollender Thanks everyone:
With the advice given, I found it... Apr 28 2015, 03:18 PM rhodyguy Well presented. The lever ball bushing are often o... Apr 28 2015, 11:39 PM pgollender
....The contact edge of the detention plate is pr... Apr 29 2015, 11:40 PM rhodyguy this is a pretty clean detent plate. junked up spr... Apr 29 2015, 11:51 AM rhodyguy Yes, pelican. I had missed the picture showing the... Apr 30 2015, 06:30 AM maf914 Some what off topic, but, Weltmeister offered a ki... Apr 30 2015, 08:04 AM rhodyguy Over kill. I bought into the hype and promptly too... Apr 30 2015, 08:21 AM rhodyguy iirc with the spring kit as per instructions you d... Apr 30 2015, 10:19 AM johnhora nice write up pgollender...
I made this tool a lo... Apr 30 2015, 02:51 PM malcolm2
nice write up pgollender...
I made this tool a l... Apr 30 2015, 03:54 PM malcolm2
Waiting on the tranny to return so i took my si... Apr 30 2015, 04:02 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 4th June 2025 - 09:06 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.