 temp gauge |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| arsprod |
 May 17 2015, 04:26 PM
Post
#1
|
|
Member  Group: Members Posts: 210 Joined: 14-March 15 From: Indianapolis Member No.: 18,519 Region Association: Upper MidWest  |
The temp gauge above my fuel gauge isn't working. For the life of me I cannot find any mention of it in the Haynes manual I have or even in the owners manual. Where's the sending unit for this thing? 74 2.0
|
   |
 
|
  |
Replies
| arsprod |
Jun 22 2015, 10:15 AM
Post
#2
|
|
Member Group: Members Posts: 210 Joined: 14-March 15 From: Indianapolis Member No.: 18,519 Region Association: Upper MidWest |
Follow up with some potentially helpful info for future readers - I got my temp gauge working (yay). The VDO sender I referenced earlier does work and Pelican stocks them, part #323055-M82. Another discovery - there's a bundle of connectors below the stickshift, underneath the heater indicator and carpet. I wished someone would have mentioned that earlier - the wire from the sender to my gauge was disconnected for some unknown reason. I discovered this after I'd already replaced the sender... oh well!
|
|
|
|
| stugray |
Jun 22 2015, 12:48 PM
Post
#3
|
|
Advanced Member Group: Members Posts: 3,825 Joined: 17-September 09 From: Longmont, CO Member No.: 10,819 Region Association: None |
QUOTE(arsprod @ Jun 22 2015, 10:15 AM)  - the wire from the sender to my gauge was disconnected for some unknown reason. I discovered this after I'd already replaced the sender... oh well! QUOTE(stugray @ Jun 14 2015, 04:00 PM) To test the gauge, with ignition on disconnect the wire from the temp sensor and ground it to the engine bar. The gauge should read the Highest temp it is capable of. Glad you got it working! |
|
|
|
Posts in this topic
arsprod temp gauge May 17 2015, 04:26 PM
type47
Where's the sending unit for this thing?
L... May 17 2015, 05:28 PM arsprod Thank you! I was looking at that yesterday tho... May 17 2015, 05:33 PM 914Sixer Wire is green with red stripe. Heat and time have... May 17 2015, 07:30 PM
arsprod
Wire is green with red stripe. Heat and time hav... May 23 2015, 11:28 AM type47
Could it be green/black on 74?
http://www.peli... May 23 2015, 03:48 PM arsprod
Could it be green/black on 74?
http://www.pel... May 23 2015, 06:13 PM SKL1 Get a new sending unit for the taco plate and put ... May 23 2015, 09:25 PM steuspeed
... I sent my gauge to North Hollywood Speedomet... May 24 2015, 01:08 AM arsprod
Get a new sending unit for the taco plate and put... May 24 2015, 06:57 AM arkitect
Get a new sending unit for the taco plate and put... May 24 2015, 08:24 AM arsprod This the correct part? http://www.egauges.com/Prod... May 24 2015, 07:44 AM Java2570
This the correct part? http://www.egauges.com/Pro... May 24 2015, 08:43 AM bdstone914
[quote name='arsprod' post='2190641' date='May 24... May 24 2015, 12:08 PM brant I am facing the same problem
is there anyway to te... May 24 2015, 10:07 AM bdstone914 Measure the resistance from the center terminal to... May 24 2015, 12:03 PM Java2570 This thread has a ton of good oil temp info: http:... May 24 2015, 02:56 PM arsprod Hmm... maybe just replacing wire is the answer May 24 2015, 05:55 PM SKL1 Here's a picture of the gauge panel before I p... May 24 2015, 06:36 PM arsprod So I've confirmed a connection from sender to ... May 31 2015, 07:56 AM forrestkhaag I recently went thru this issue with my newly rewo... May 31 2015, 08:54 AM arsprod
I recently went thru this issue with my newly rew... May 31 2015, 09:00 AM arsprod Back at this - I've ordered a sender finally b... Jun 14 2015, 03:21 PM stugray + to +12VDC (dash power)
GND to chassis ground
Th... Jun 14 2015, 04:00 PM arsprod
+ to +12VDC (dash power)
GND to chassis ground
T... Jun 14 2015, 05:40 PM stugray
Thank you - appears mine is missing a lead to gr... Jun 14 2015, 06:57 PM arsprod
Thank you - appears mine is missing a lead to g... Jun 15 2015, 08:17 AM arsprod
- the wire from the sender to my gauge was disc... Jun 22 2015, 01:15 PM stugray
Thanks, me too! Just noticed your signature -... Jun 22 2015, 04:04 PM arsprod
Thanks, me too! Just noticed your signature ... Jun 22 2015, 05:51 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 12:20 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.