 Broke bolt for trunk latch..., suggestions on repair requested |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| dangerranger01 |
 Oct 2 2015, 09:09 PM
Post
#1
|
|
Member  Group: Members Posts: 145 Joined: 12-August 05 From: Boring, Oregon U.S.A. Member No.: 4,578 Region Association: None  |
Just my luck, i snapped off a bolt that held the rear trunk latch on. Pulling it to replace the spring that broke. Anyone else experience this?? I'd venture to say that tig welding a head on to get a wrench on wouldn't work....probably snap that off too.
Oh, and I snapped an easy-out in it too. Just great!! What do you think of welding a short stud on...looks like there is enough room for no interfence with the bottom latch assembly....I need a beer. (IMG:http://www.914world.com/bbs2/uploads_offsite/i718.photobucket.com-4578-1443841759.1.jpg) Oh, and the other bolt that did come out thread's looked nasty.... (IMG:http://www.914world.com/bbs2/uploads_offsite/i718.photobucket.com-4578-1443841759.2.jpg) |
   |
 
|
  |
Replies
| dangerranger01 |
Oct 10 2015, 05:35 PM
Post
#2
|
|
Member Group: Members Posts: 145 Joined: 12-August 05 From: Boring, Oregon U.S.A. Member No.: 4,578 Region Association: None |
It looks like there is that spray foam crap behind the thread inserts....anyone know if that is that flammable?
I figure worst case is I try to build a bead up with my TIG to then weld a nut on. If the bigass breaker bar can't take it off then, I'll cut it out and patch a piece of sheetmetal wiht a nut welded on the inside as the thread to hold the latch on. What a pita.... |
|
|
|
Posts in this topic
dangerranger01 Broke bolt for trunk latch... Oct 2 2015, 09:09 PM
dangerranger01 Might try this....but i think that bolt is rusted ... Oct 2 2015, 09:13 PM jsh What about drilling it out and then tapping Oct 2 2015, 10:31 PM steuspeed Rusted stud at the 7:00min mark.
You could also ... Oct 2 2015, 10:43 PM jeffdon You guys have trunk latches? Oct 2 2015, 10:48 PM RobW Start with a small drill bit, then use PB blaster.... Oct 3 2015, 04:12 AM MMW Looks to be below flush with surface? This is why... Oct 3 2015, 07:27 AM cary When you get there. I think I have a hood we can u... Oct 11 2015, 07:50 AM
Spoke What about welding on a bolt, cut the head off and... Oct 11 2015, 09:34 AM Hank914
What about welding on a bolt, cut the head off an... Oct 11 2015, 10:30 AM RobW
What about welding on a bolt, cut the head off an... Oct 11 2015, 10:37 AM dangerranger01 Well I fixed it. Tried to build a bead up with my ... Nov 17 2015, 07:20 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 2nd April 2026 - 11:14 AM |
Invision Power Board
v9.1.4 © 2026 IPS, Inc.