 Oil Galley Plugs, Just replace the five big ones? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| saigon71 |
 Jan 18 2016, 01:49 PM
Post
#1
|
|
Advanced Member  Group: Members Posts: 2,014 Joined: 1-June 09 From: Dillsburg, PA Member No.: 10,428 Region Association: MidAtlantic Region 
 |
In preparation for an engine rebuild, I wanted to get myself up to speed on drilling/tapping the oil galley plugs.
Search revealed conflicting information about whether all should be removed and tapped or just the five big ones. What's the current school of thought on this? Also, what size plugs and drill/tap will I need. Thanks! http://www.914world.com/bbs2/index.php?sho...=103988&hl= |
   |
 
|
  |
Replies
| rhcb914 |
Jan 19 2016, 08:06 PM
Post
#2
|
|
member Group: Members Posts: 360 Joined: 3-February 04 From: Boston, MA Member No.: 1,626 |
I bought a box of 100 steel hex hed plugs from Grainger. It was like $20.
Harbor Freight has a $12 tap kit which I bought 2 of. Grind down the lead of 1 tap. Use the full tap to start the threads then chase with the ground down tap. Cut a little check the depth of the plug. Repeat until the plugs are just slightly proud of the case. Make sure you clean the galleys really well! |
|
|
|
Posts in this topic
saigon71 Oil Galley Plugs Jan 18 2016, 01:49 PM
Porschef Bob, I did mine as a precaution before installing ... Jan 18 2016, 05:52 PM Mark Henry 3/8" NPT pipe tap, 9/16 drill bit use steel p... Jan 19 2016, 08:15 AM
r_towle
3/8" NPT pipe tap, 9/16 drill bit use steel ... Jan 19 2016, 08:29 AM Mark Henry
Where did you order the allen head plugs?
Prett... Jan 19 2016, 09:02 AM Dave_Darling IIRC, there is one plug that will block an importa... Jan 19 2016, 10:33 AM Mark Henry
IIRC, there is one plug that will block an import... Jan 19 2016, 11:33 AM McMark McMaster has them. Jan 19 2016, 10:36 AM Jake Raby I'm building a 2270 for a World member now.. L... Jan 19 2016, 09:57 PM saigon71 Thanks for the responses and recommendations. :b... Feb 2 2016, 08:29 PM rdauenhauer are those steel or Alum. plugs? Feb 2 2016, 10:10 PM saigon71
are those steel or Alum. plugs?
Steel. Feb 3 2016, 08:10 AM Olympic 1.7 When I did mine I got an extra tap and ground the ... Feb 3 2016, 08:30 AM McMark :agree: A second tap is handy.
Also, when drillin... Feb 3 2016, 08:35 AM Mark Henry
:agree: A second tap is handy.
Also, when drilli... Feb 3 2016, 10:20 AM McMark Oh yeah. That for sure! :agree: Feb 3 2016, 12:58 PM nathansnathan When I did this the 1st time, I had got some 3/8... Feb 3 2016, 05:14 PM Mark Henry
When I did this the 1st time, I had got some 3/8... Feb 3 2016, 08:38 PM nathansnathan
When I did this the 1st time, I had got some 3/8... Feb 4 2016, 12:03 AM Mark Henry
[quote name='Mark Henry' post='2298151' date='Feb... Feb 4 2016, 07:38 AM McMark Wd-40 is better than goo-gone for removing stick r... Feb 3 2016, 09:50 PM nine9three I've always used JB Weld to seal mine. Never... Feb 4 2016, 12:11 AM Puebloswatcop WD40 does a fair job, but if you want really clean... Feb 4 2016, 08:31 AM McMark I love how these threads go awry. :lol:
Is cuttin... Feb 4 2016, 09:04 AM 914_teener
I love how these threads go awry. :lol:
Is cutti... Feb 4 2016, 09:35 AM pilothyer You can spend the money on special for aluminum ... Feb 4 2016, 09:20 AM Mark Henry
You can spend the money on special for aluminum ... Feb 4 2016, 10:59 AM McMark Had to. This got way too dramatic over WD-40. :r... Feb 4 2016, 09:40 AM Mark Henry
Had to. This got way too dramatic over WD-40. :... Feb 4 2016, 10:20 AM Mark Henry Now I have it pretty well flush, BTW I'll be d... Feb 4 2016, 10:23 AM Mark Henry This came out good :)
This show the one plug you ... Feb 4 2016, 10:31 AM Mark Henry The last pic shows 3 different steel plugs.
The on... Feb 4 2016, 10:43 AM saigon71 Thanks for all the technical support on this...esp... Mar 13 2016, 05:13 PM Mark Henry :thumbsup:
Good job! Mar 13 2016, 08:42 PM |
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 23rd June 2025 - 10:04 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.