 Thermostat Questions |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| orbit398 |
 Jan 25 2016, 10:39 AM
Post
#1
|
|
Member  Group: Members Posts: 139 Joined: 29-April 15 From: League city, Texas Member No.: 18,681 Region Association: Southwest Region  |
Putting my engine back together and have a few questions on the thermostat. I did the check to make sure it grows to the proper length (1.81" at 150 -160 degree water) and it seems close enough. Air flappers all operate fine, accept I think there is a little interference with the drivers side flap. If I try to close the flap all the way, it appears to hit a small piece on the aluminum large air bracket. See pics. I can't shift that flapper door down the bar a bit allowing it to clear this small piece of aluminum sticking out. I can modify the flapper a bit so it'd close all the way but figured I'd ask folks.
Next Question, are there instructions on how to adjust the cable operation of the air flappers. I assume I need to pull the thermostat to it's extended length and secure the small cable to the flapper bar location at that cable length. The result being that when the thermostat is extended, the cable should allow the flapper bar spring to fully open the air flappers. thanks for any advice Attached image(s)  
|
   |
 
|
  |
Replies
| rhodyguy |
Jan 28 2016, 05:24 PM
Post
#2
|
|
Chimp Sanctuary NW. Check it out. Group: Members Posts: 22,252 Joined: 2-March 03 From: Orion's Bell. The BELL! Member No.: 378 Region Association: Galt's Gulch |
Perhaps that is a better way. I don't know. Do the factory manuals include this procedure?
|
|
|
|
Posts in this topic
orbit398 Thermostat Questions Jan 25 2016, 10:39 AM
ndfrigi In regards to the driver side flap, i believed it ... Jan 25 2016, 10:48 AM cuddyk The flap doesn't have to go all the way down. ... Jan 25 2016, 03:58 PM
The Cabinetmaker
The flap doesn't have to go all the way down.... Jan 25 2016, 08:28 PM cuddyk
The flap doesn't have to go all the way down... Jan 26 2016, 07:41 AM Tbrown4x4 My cable had come off the pulley. I used a heat gu... Jan 26 2016, 04:00 AM rhodyguy With the cable unattached the vanes should be in t... Jan 26 2016, 10:17 AM mankowski In my experience, it's better to tighten the c... Jan 26 2016, 11:01 PM orbit398
With the cable unattached the vanes should be in ... Jan 28 2016, 02:43 PM rhodyguy As for the default state, the clamping tab is near... Jan 28 2016, 03:56 PM rhodyguy As for reply #8, I think one should check for full... Jan 28 2016, 04:20 PM Dave_Darling I always got the car to operating temp (or close t... Jan 28 2016, 04:32 PM 914ltd As for the workshop manual, it gives only the heat... Jan 30 2016, 08:26 AM BeatNavy
I am almost out of good used thermostats, I'm... Jan 30 2016, 12:33 PM 914ltd
I am almost out of good used thermostats, I... Jan 30 2016, 01:09 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 2nd April 2026 - 11:41 AM |
Invision Power Board
v9.1.4 © 2026 IPS, Inc.