 Low Oil Pressure on Hard Deceleration, 2.056L with Dual Carbs |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Spoke |
 Sep 12 2016, 11:01 AM
Post
#1
|
|
Jerry  Group: Members Posts: 7,158 Joined: 29-October 04 From: Allentown, PA Member No.: 3,031 Region Association: None 
 |
I bought this allegedly running-when-it-was-pulled 2L engine last year to upgrade to 2.056L just to find out it already had 96mm P&C.
Internals turns smoothly so I thought I'd do the flame test and clean the engine and put it back together. The engine runs strong and smooth. As I started driving it harder I noticed on fast deceleration the oil light would come on. If I let the engine speed come down naturally from about 2k, the oil light doesn't come on. Last night coming off the highway running about 3.2k, I immediately shifted into neutral to let the engine slow on its own, the oil light came on for a few seconds as the engine was now idling. I don't have an oil pressure gauge on it to see where the oil pressure is during operation. Any ideas of what to look at? Attached thumbnail(s) 
|
   |
 
|
  |
Replies
| VaccaRabite |
Sep 13 2016, 07:39 AM
Post
#2
|
|
En Garde! Group: Admin Posts: 13,729 Joined: 15-December 03 From: Dallastown, PA Member No.: 1,435 Region Association: MidAtlantic Region
|
Internal clearances may be too high.
But I would check all the other stuff first, and get a pressure gauge on there asap. Until you know what your pressure is dropping to, all we are doing is spit balling. I don't like the dual pole senders, BTW. They have the idiot light set at about 9 PSI, much higher then the stock sender. I have a single pole pressure sender, and a stock idiot light sender on a Y block. |
 |
|
| Spoke |
Sep 13 2016, 08:26 AM
Post
#3
|
|
Jerry Group: Members Posts: 7,158 Joined: 29-October 04 From: Allentown, PA Member No.: 3,031 Region Association: None
|
QUOTE(Vacca Rabite @ Sep 13 2016, 09:39 AM)  I have a single pole pressure sender, and a stock idiot light sender on a Y block. About the Y block, is this the metal plumbing Y available at hardware stores or special brass Y? Got a pic? Also, where to buy an oil pressure gauge and sender? I didn't see anything on Pelican. |
|
|
|
Posts in this topic
Spoke Low Oil Pressure on Hard Deceleration Sep 12 2016, 11:01 AM
Tom_T Spoke,
Both my `73 914-2.0 & our `88 ... Sep 12 2016, 11:21 AM Vacca Rabite Chris Foley was selling a pressure booster that re... Sep 12 2016, 12:54 PM
boxsterfan
Chris Foley was selling a pressure booster that r... Sep 12 2016, 01:00 PM brant I'd replace the sending unit too.
put on a dua... Sep 12 2016, 01:10 PM The Cabinetmaker I don't think Chris' valve was intended to... Sep 12 2016, 01:41 PM '73-914kid I would recommend installing a tuna can on the sum... Sep 12 2016, 03:00 PM '73-914kid Also, what oil and weight? Sep 12 2016, 03:01 PM Spoke
Also, what oil and weight?
Valvoline VR1 20W-50... Sep 12 2016, 08:32 PM 914Bryan I agree with what Ethan said about overfilling the... Sep 12 2016, 03:14 PM Dave_Darling Every time I have had the oil light come on under ... Sep 12 2016, 08:04 PM Dave_Darling
Also, where to buy an oil pressure gauge and send... Sep 13 2016, 09:33 AM colingreene Do you know for sure that the windage tray is in i... Sep 13 2016, 11:46 PM Spoke
Do you know for sure that the windage tray is in ... Sep 14 2016, 01:19 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 11th May 2025 - 11:04 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.