 Problem with fuel gauge., Shows only 1/4 full. |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| daytona |
 Feb 4 2018, 03:48 PM
Post
#1
|
|
daytona  Group: Members Posts: 467 Joined: 13-April 14 From: Ormond Beach, Florida Member No.: 17,249 Region Association: South East States  |
Hi world,
I need some help with the fuel gauge in my 74. The car is a 6 cylinder conversion but I don't think that this factor contributes to the problem. The issue is that the gauge shows that the tank is 1/4 full even though it is full to the top. I have two other gauges that I tried and both show the same 1/4 tank level. In my book this would indicate that the sending unit is the culprit. Couldn't be that all three gauges have the same defect. However, measuring the voltage at the gauge, I get 12.4VDC. I think this means that the sending unit is sending the correct signal. So where is the problem??? Has anyone had this problem? Any ideas? Any and all help is appreciated. Thanks, Bill. |
   |
 
|
  |
Replies
| Tbrown4x4 |
Feb 5 2018, 08:52 PM
Post
#2
|
|
Senior Member Group: Members Posts: 707 Joined: 13-May 14 From: Port Orchard, WA Member No.: 17,338 Region Association: None 
|
I just had mine apart, and I don't remember having to un-crimp the bottom. I think if you gently wiggle the tube back and forth, it separated at the top. It has been on there for 40+ years!
BTW, my sending unit had 66.9 ohms empty and 9.2 ohms full. |
|
|
|
Posts in this topic
daytona Problem with fuel gauge. Feb 4 2018, 03:48 PM
dr914@autoatlanta.com Remove the sending unit, take it apart, and clean ... Feb 4 2018, 03:50 PM daytona dr914, OK thanks.
So you are saying that as the fl... Feb 4 2018, 04:01 PM
dr914@autoatlanta.com 0-90 ohms resistance to the gauge, When it gets s... Feb 4 2018, 04:07 PM GeorgeRud The sender is basically a variable resistor, so yo... Feb 4 2018, 05:38 PM Tbrown4x4 Some of your terminology is off, so hopefully this... Feb 5 2018, 06:01 AM daytona Hi guys,
I removed the sending unit from a spare t... Feb 5 2018, 03:40 PM daytona Anybody?
I removed the small nut on the bottom of ... Feb 5 2018, 05:25 PM Olympic 914 Yes. remove the little nut on the bottom, carefull... Feb 5 2018, 05:34 PM daytona I have not been able to take it apart yet. I have ... Feb 5 2018, 06:41 PM windforfun You can get a brand new OEM Bosch unit for about ... Feb 5 2018, 06:48 PM PanelBilly I bought a new one from Sunset Porsche. It’s s n... Feb 5 2018, 09:07 PM daytona Hi again guys,
Last knight I was just being an idi... Feb 6 2018, 12:16 PM The Cabinetmaker Your connectors should be in a plug that only plug... Feb 6 2018, 12:38 PM daytona Cabinetmaker,
Yes, that is the plug at the sending... Feb 6 2018, 06:34 PM Mike Fitton Here you go.
Feb 6 2018, 07:09 PM daytona Thank you Mike.
Bill. Feb 7 2018, 06:17 AM Morrie Hi Guys,
My connector at the sending unit was bro... Feb 7 2018, 09:57 AM daytona Hi all,
fuel gauge problem solved. As several of y... Feb 11 2018, 06:12 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 8th July 2025 - 03:56 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.