![]() |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
![]() |
motorvated |
![]()
Post
#1
|
Member ![]() ![]() Group: Members Posts: 281 Joined: 13-February 13 From: Colorado Member No.: 15,519 Region Association: Rocky Mountains ![]() |
I had my 1.8 L Jet motor with Bursch exhaust running well with immediate start up, smooth idle, and strong running up to redline. Removed the Bursch and replaced it with a tuned header with megaphone exhaust and now it's so lean that it won't run below 2000 rpm, and won't idle. It starts on the key with no pedal but dies immediately. If I work the pedal when cranking, I can get it to run, but only at higher rpm. With the Bursch I had it set to run with AFR of around 10-12 at higher rpm, and around 15 at idle. Now it's 15-16 at high rpm and it hits the max reading of 19 on the gauge as it drops from 2000 rpm and stalls.
Ignition and timing have been set and verified, and I have once again been trying to make sure that I have no vacuum leaks. Bursch had a fitting for EGR, and I had that hooked up when it was running well, but new exhaust has no EGR fitting so I have blinded it off for no flow. Tried it open to atmosphere but that didn't help or make things any worse. AAR and Decel valve both still hooked up. Tried disconnecting and plugging vacuum lines to EGR and Decel valves with no change. I'd like to remove them but I'm unsure of how best to plug them off so I don't create any new vacuum leaks. Could use some advice there. Before I go back into the AFM box to start re-adjusting things, I'd like to know if others have had similar problems when switching to a free flow performance exhaust. Should I have expected to have to re-adjust the AFM settings to richen the mixture because of the more free flowing exhaust, or do you think I have a new problem that I need to find and address first. All comments/suggestions welcome. |
![]() ![]() |
ChrisFoley |
![]()
Post
#2
|
I am Tangerine Racing ![]() ![]() ![]() ![]() ![]() Group: Members Posts: 7,937 Joined: 29-January 03 From: Bolton, CT Member No.: 209 Region Association: None ![]() ![]() |
That's too rich across the board.
Adjust the wiper for 12.5 at WOT. You can adjust the idle mixture with the bypass screw in the pocket on top of the flapper box. |
motorvated |
![]()
Post
#3
|
Member ![]() ![]() Group: Members Posts: 281 Joined: 13-February 13 From: Colorado Member No.: 15,519 Region Association: Rocky Mountains ![]() |
That's too rich across the board. Adjust the wiper for 12.5 at WOT. You can adjust the idle mixture with the bypass screw in the pocket on top of the flapper box. Another half day dinking with the AFM and I now see that changing this exhaust has put the L Jet just beyond its adjustment limitations. When I adjust the dynamic setting (the big gear that controls the tension to the wiper spring) to lean out the mixture at high rpm, my idle and mid-range go too lean. To fix that, I richen the static adjustment (the position of the wiper on the spring loaded arm), and this makes the spring on the wiper arm a little weaker, richening the top end mixture. After walking through this pattern of adjustments and trimming idle mixture with the bypass screw along the way, I reached a point where the static and dynamic adjustments were just too far away from each other and to eliminate a mid-range lean miss, I had to reduce the dynamic wiper arm spring tension, and by doing that, I lost the high rpm mixture as it went rich as the wiper arm went beyond the optimal position. So I'm thinking of physically limiting the maximum amount of wiper arm travel so the high end mixture will be optimized rather than going rich While maintaining a good idle and strong mid-range. It's either this or back to the old exhaust. |
![]() ![]() |
![]() |
Lo-Fi Version | Time is now: 18th June 2024 - 01:00 AM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |