 Seat Frame: New Challenge, Reassembly & Seat Handle Rails |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| 914_7T3 |
 Mar 2 2019, 12:58 PM
Post
#1
|
|
Please forgive me, I'm new to all of this!  Group: Members Posts: 1,875 Joined: 3-April 17 From: Los Angeles, CA Member No.: 20,991 Region Association: Southern California 
 |
Looking to have my seat frames powder coated and need to remove the non-painted handle assembly as it contains plastic bushings that will melt at high temperature.
Any idea on the correct procedure and tools required for removal?  |
   |
 
|
  |
Replies
| bbrock |
Mar 17 2019, 10:57 PM
Post
#2
|
|
914 Guru Group: Members Posts: 5,269 Joined: 17-February 17 From: Montana Member No.: 20,845 Region Association: Rocky Mountains
|
That kit is what I installed. The roll pins that come with the kit are too big. You either have to drill the holes in the levers larger or grind the pins to make more clearance for them to close to a smaller diameter. I decide to just reuse the old pins. The special tool is like Mark said, it is just to help you set the depth of the pin. It's just a piece of round stock with a hole drilled in it. You put the pin in the hole and then drive it in with the tool. When the tool bottoms out, the pin is at the correct depth.. ish. I had to tap mine in a little more.
Anyway, the kit is good, but don't get too excited about it making the job easier. |
|
|
|
Posts in this topic
914_7T3 Seat Frame: New Challenge Mar 2 2019, 12:58 PM
bbrock Just a drift to drive out the roll pin that the sp... Mar 2 2019, 02:03 PM
914_7T3
Just a drift to drive out the roll pin that the s... Mar 2 2019, 02:32 PM 914_7T3 Got the frames back from Powder Coating and cleane... Mar 17 2019, 07:26 PM bbrock First. Make sure you have plenty of coins to put ... Mar 17 2019, 07:36 PM 914_7T3
First. Make sure you have plenty of coins to put... Mar 17 2019, 08:13 PM bbrock
Ok, so does that mean securing the spring to the ... Mar 17 2019, 09:24 PM 914_7T3
Ok, so does that mean securing the spring to the... Mar 17 2019, 10:21 PM mepstein Didn't 914rubber make a tool for winding or se... Mar 17 2019, 08:31 PM 914_7T3
Didn't 914rubber make a tool for winding or s... Mar 17 2019, 08:39 PM mepstein
[quote name='mepstein' post='2697677' date='Mar 1... Mar 17 2019, 08:48 PM 914_7T3
[quote name='914_7T3' post='2697679' date='Mar 17... Mar 17 2019, 10:25 PM Mikey914 Yes the tool holds the pin so you can get it insta... Mar 18 2019, 06:07 AM bbrock
As far as the roll pins I actually used the ones ... Mar 18 2019, 07:38 AM Mikey914 Either way I'll take a look too this next week... Mar 18 2019, 03:23 PM Olympic 914 Bolted the seat rails to work table and used a wir... Mar 18 2019, 05:08 PM mepstein
Bolted the seat rails to work table and used a wi... Mar 18 2019, 06:07 PM 914_7T3
Bolted the seat rails to work table and used a wi... Apr 21 2019, 10:39 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 11:27 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.